manualshive.com logo in svg

Alliance Laundry Systems UWT021LA, Руководство по обслуживанию

Поделиться
Скачать
Alliance Laundry Systems UWT021LA Скачать руководство пользователя страница 41

42

39201

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the washer is properly grounded.

W003

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

29. CABINET TOP ASSEMBLY

a. Remove two screws from bottom edge of front 

panel. Refer to Figure 37.

b. Pull bottom of panel away from washer until 

hold down clips (located on top flange of panel) 
disengage from slots in cabinet top.

c. METERED MODELS:

(1) Unlock and remove meter case service 

door.

(2) Remove timer bracket cap screw. Refer to 

Figure 8.

(3) Slide timer and bracket toward rear of 

meter case to disengage bracket from 
shoulder screw. Lift timer and bracket out 
of meter case through service door opening 
as far as wires will permit.

(4) Remove shoulder screw from inside meter 

case.

(5) Remove two cabinet top hold down screws. 

Refer to Figure 37.

(6) Remove security bolt (if present) from left 

rear corner of cabinet top.

NOTE: When lowering cabinet top into position or 
reinstalling cabinet top, pivot outer tub forward far 
enough to prevent damaging (bending) loading door 
switch lever.

d. Tape loading door closed and lift cabinet top to 

a vertical position by hinging it on the rear 
hinges.

NOTE: Cabinet top is self supporting, however, a 
small chain may be used for additional support. 
Refer to Figure 38.

TO REMOVE CABINET TOP FROM 
WASHER
a. Remove two control panel attaching screws. 

Refer to Figure 5. Lay assembly forward on a 
protective pad on cabinet top. 

b.  Disconnect pressure hose from pressure 

switch. Refer to Figure 6.

IMPORTANT: When installing pressure hose, blow 
air into hose before connecting hose to switch to 
remove any moisture that may have accumulated in 
the hose.

c. Push base wire harness block and pressure hose 

down through hole in cabinet top.

d. Tape loading door closed.

e. Reinstall control panel and screws.

f. Remove two screws from bottom edge of front 

panel. Refer to Figure 37.

g. Pull bottom of panel away from washer until 

hold-down clips (located on top flange of 
panel) disengage from slots in cabinet top.

h. METERED MODELS:

(1) Unlock and remove meter case service 

door.

(2) Remove timer bracket cap screw. Refer to 

Figure 9.

(3) Slide timer and bracket toward rear of 

meter case to disengage bracket from 
shoulder screw. Lift timer and bracket out 
of meter case through service door opening 
as far as wires will permit.

(4) Remove shoulder screw from inside meter 

case.

(5) Remove two cabinet top hold down screws. 

Refer to Figure 37.

Figure 38

CHAIN

W252SE1A

Содержание UWT021LA




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды