manualshive.com logo in svg

Alliance Laundry Systems UWT021LA, Руководство по обслуживанию

Поделиться
Скачать
Alliance Laundry Systems UWT021LA Скачать руководство пользователя страница 42

39201

43

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the washer is properly grounded.

W003

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

(6) Remove security bolt (if present) from left 

rear corner of cabinet top.

NOTE: When lowering cabinet top into position or 
reinstalling cabinet top, pivot outer tub forward far 
enough to prevent damaging (bending) loading door 
switch lever.

i. Lift front of cabinet top slightly and pull 

forward to disengage from rear hinges.

j. Pull top forward far enough to permit 

disconnecting ground wires from top rear 
corner gusset of washer cabinet. Refer to 
Figure 39. Disconnect wires from mixing valve 
solenoids at rear of washer.

NOTE: Refer to appropriate wiring diagram when 
rewiring mixing valve solenoids.

k. Carefully lift cabinet top off washer and set on 

protective padding.

IMPORTANT: When reinstalling cabinet top and 
before lowering top into position, pivot outer tub 
forward far enough to prevent damaging (bending) 
door switch lever.

To reduce the risk of serious injury, be 
careful not to damage door switch when 
removing cabinet top.

W180

WARNING

Figure 39

W497SE3B

PRESSURE

HOSE

CORNER

GUSSET

GROUND

WIRE

MIXING

VALVE

WIRE

HARNESS

DISCONNECT

BLOCKS

DOOR

SWITCH

Содержание UWT021LA




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды