manualshive.com logo in svg

Alliance Laundry Systems UWT021LA, Руководство по обслуживанию

Поделиться
Скачать
Alliance Laundry Systems UWT021LA Скачать руководство пользователя страница 52

39201

53

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the washer is properly grounded.

W003

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

g. If area or space permits, tape loading door 

closed and lift cabinet top to a vertical position 
by hinging it on the rear hinges. Refer to 
Figure 38.

NOTE: Cabinet top is self supporting, however, a 
small chain may be used for additional support. 
Refer to Figure 38.

h. Loosen hose clamp and remove filler hose from 

outer tub cover. Refer to Figure 46.

NOTE: When installing filler hose, white line on 
hose must point toward front of washer. Refer to 
Figure 46.

i. There are eight tub cover hold-down tabs which 

snap over outer tub flange. Place your fingers 
under the flap of the hold-down tab of the tub 
cover. Pull out on flap and at the same time lift 
upward on cover to unsnap hold-down tabs 
from outer tub flange. One by one, disengage 
each of the eight hold-down tabs from outer tub 
flange and remove cover.

IMPORTANT: When installing outer tub cover, 
always use a new cover gasket.

NOTE: Clean and remove any foreign material in 
gasket groove of outer tub cover and outer tub 
flange.

j. Starting at positioning pin, lay gasket into 

gasket groove of tub cover. Refer to Figure 47.

k. Using your fingers, press gasket down into 

gasket groove of tub cover. Avoid pressing 
gasket past ends of hold-down tabs.

IMPORTANT: Care must be taken not to twist or 
bunch gasket in any one area to avoid leaks after 
assembly.

l. Install gasket past ends of hold-down tabs to 

bottom of gasket groove using semi-circled end 
of tool Part No. 273P4. Refer to Figure 47.

NOTE: Tub cover gasket tool, Part No. 273P4, is 
designed to spread open hold-down tabs to prevent 
tearing of gasket during installation.

m. With tub cover tilted at approximately a 45 

degree angle, insert the positioning pin into 
notch on outer tub flange.

n. Lower cover and push down firmly on top of 

hold- down tabs next to positioning pin until 
tabs snap over edge of outer tub flange.

o. Cross over to opposite side of tub cover and 

push down firmly on top of hold-down tabs 
until tabs snap over edge of outer tub flange. 
Continue with this criss-cross pattern, until tub 
cover is fully seated. Visually check each tab 
area again to ensure cover is seated.

Figure 47

W479SE3A

HOLD DOWN

TABS

TUB

COVER

GASKET

273P4 

TUB COVER 

GASKET TOOL

PRESS GASKET

INTO GROOVE USING

YOUR FINGERS

Содержание UWT021LA




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды