manualshive.com logo in svg

Alliance Laundry Systems UWT021LA, Руководство по обслуживанию

Поделиться
Скачать
Alliance Laundry Systems UWT021LA Скачать руководство пользователя страница 51

52

39201

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the washer is properly grounded.

W003

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

36. WASHTUB AND BALANCE RING

a. Open loading door.
b. Remove agitator by placing two agitator hooks, 

No. 254P4P, under bottom edge of agitator. 
Refer to Figure 29.

IMPORTANT: Hooks should be positioned 180 
degrees from each other, and must be placed under 
agitator vane for greater stability. If hooks are 
placed between vane area, agitator damage may 
occur.

c. Using a rocking motion (back and forth) 

carefully lift agitator off drive bell.

d. Remove two screws from bottom edge of front 

panel. Refer to Figure 37.

e. Pull bottom of panel away from washer until 

hold down clips (located on top flange of panel) 
disengage from slots in cabinet top.

f. METERED MODELS:

(1) Unlock and remove meter case service 

door.

(2) Remove timer bracket cap screw. Refer to 

Figure 9.

(3) Slide timer and bracket toward rear of 

meter case to disengage bracket from 
shoulder screw. Lift timer and bracket out 
of meter case through service door opening 
as far as wires will permit.

(4) Remove shoulder screw from inside meter 

case.

(5) Remove two cabinet top hold down screws. 

Refer to Figure 37.

(6) Remove security bolt (if present) from left 

rear corner of cabinet top.

NOTE: When lowering cabinet top into position or 
reinstalling cabinet top, pivot outer tub forward far 
enough to prevent damaging (bending) loading door 
switch lever.

Figure 46

W478SE3C

HOLD DOWN

TABS

OUTER TUB

COVER

FILLER

HOSE

HOSE

CLAMP

LOADING DOOR

SWITCH LEVER

Содержание UWT021LA




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды