manualshive.com logo in svg

Alliance Laundry Systems UWT021LA, Руководство по обслуживанию

Поделиться
Скачать
Alliance Laundry Systems UWT021LA Скачать руководство пользователя страница 16

16

39201

Section 3 Troubleshooting

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the washer is properly grounded.

W003

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

12. WASHER STOPS IN CYCLE; QUITS AFTER A COUPLE LOADS; IS INTERMITTENT

13. WASHER IS LOCKED UP OR BINDING

14. OUTER TUB DOES NOT EMPTY

POSSIBLE CAUSE

TO CORRECT

Belt is tacky and does not allow proper slip.

• Check belt and replace if defective.

Belt tension is too great and does not allow proper 
slip.

• Make sure idler spring is properly connected.

Inoperative timer.

• Test timer and replace if inoperative.

Broken, loose or incorrect wiring.

• Refer to appropriate wiring diagram.

Motor overload protector has cycled.

• Wait two or three minutes for overload protector to reset. 

If protector cycles repeatedly, refer to Paragraph 9.

Motor switch functions inoperative.

• Refer to Section 7 to check switch functions.

Brake, transmission or motor has locked up and will 
not turn.

• Check that all these components are able to move freely.

POSSIBLE CAUSE

TO CORRECT

Excessive belt tension.

• Replace belt and/or idler spring.

Bind in upper or lower bearing.

• Replace bearing.

Bind in water pump.

• Replace pump.

Bind in transmission.

• Repair or replace transmission.

Brake pads binding.

• Free binding pads, or replace pads.

Incorrect voltage.

• Contact local utility company, or have a qualified 

electrician check power supply.

POSSIBLE CAUSE

TO CORRECT

Kinked drain hose.

• Straighten hose.

Drain hose out of hose retainer clip in back of 
cabinet.

• Remove washer front panel and install drain hose into 

hose retainer clip in back of cabinet.

Inoperative water pump.

• Replace pump.

Obstruction in outer tub outlet hose.

• Remove obstruction.

Содержание UWT021LA




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды