manualshive.com logo in svg

Alliance Laundry Systems UWT021LA, Руководство по обслуживанию

Поделиться
Скачать
Alliance Laundry Systems UWT021LA Скачать руководство пользователя страница 70

39201

71

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the washer is properly grounded.

W003

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

NOTE: When installing lower bearing, weldment 
assembly and brake assembly, apply No. 27604P 
Anti-Seeze Compound to area of transmission tube 
that will be contacting bearing, washtub hub and 
brake assembly. Refer to Figure 57.

To prevent porcelain damage, leg plates must be 
installed on outside of outer tub flange when 
reinstalling support legs of weldment assembly. 
Refer to Figure 54. Do not overtighten screws as this 
could cause stripping or porcelain damage. Torque 
screws between 90 to 130 inch-pounds (10.30 to 
14.87 N-m).

IMPORTANT: When replacing or reinstalling 
transmission assembly, it is important that 
No. 27604P Anti-Seeze Compound be applied to 
area of the transmission tubes where they will be 
contacting upper and lower bearings. Refer to 
Figure 57.

Carefully lower transmission through upper 
bearing. DO NOT DROP OR LOWER 
TRANSMISSION ASSEMBLY INTO POSITION 
TOO HARD. This can cause bearing to move which 
will cause vibration, noise, wear or no spin.

Figure 57

UPPER

BEARING

W450SE3C

TRANSMISSION

ASSEMBLY

APPLY 

NO. 27604P

ANTI-SEEZE
COMPOUND

TO THESE AREAS 

OF

BOTH UPPER

AND LOWER

TRANSMISSION TUBES

Содержание UWT021LA




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды