manualshive.com logo in svg

Alliance Laundry Systems UWT021LA, Руководство по обслуживанию

Поделиться
Скачать
Alliance Laundry Systems UWT021LA Скачать руководство пользователя страница 60

39201

61

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the washer is properly grounded.

W003

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

(5) Early models – Install gasket past ends of 

hold-down tabs to bottom of gasket groove 
using semi-curled end of tub cover gasket 
tool Part No. 273P4.

NOTE: Tub cover gasket tool, Part No. 273P4, is 
designed to spread open hold-down tabs to prevent 
tearing of gasket during installation.

(6) With tub cover tilted at approximately a 45 

degree angle, insert the positioning pin into 
notch on outer tub flange.

(7) Lower cover and push down firmly on top 

of hold-down tabs next to positioning pin 
until tabs snap over edge of outer tub 
flange.

(8) Cross over to opposite side of tub cover and 

push down firmly on top of hold-down tabs 
until tabs snap over edge of outer tub 
flange. Continue with this criss-cross 
pattern, until tub cover is fully seated. 
Visually check each tab area again to 
ensure cover is seated.
Refer to Figure 48.

i. Remove screws and gaskets holding washtub to 

hub. Refer to Figure 49.

IMPORTANT: Porcelain Washtub Models — Use 
care when tightening cap screws to avoid chipping 
porcelain on washtub.

j. Lift washtub (with balance ring attached) out of 

outer tub.

IMPORTANT: When removing washtub and 
balance ring, grasp top flange of washtub and 
remove from outer tub.

k. Remove agitator drive bell, Paragraph 27.

l. Remove large hex nut using No. 306P4 Hex 

Wrench. Then remove spline insert from 
transmission tube.

IMPORTANT: Use a new spline insert each time the 
hex nut is removed. DO NOT reuse the old insert as 
hex nut may loosen during the washer operation.

m. Remove hub from splines on transmission tube.

NOTE: It may be necessary to use a gear puller to 
remove hub.

n. Remove old water seal from outer tub.

IMPORTANT: Use care when removing old seal so 
as not to damage tub flange or porcelain.

NOTE: When reinstalling or replacing outer tub, 
always install a new No. 646P3 Hub and Seal Kit. 
Refer to Paragraph 37.

o. Reach in through front of motor mounting 

bracket and move idler lever to left to release 
tension on belt.

IMPORTANT: Use care when releasing idler lever 
tension. If idler lever spring is overstretched, 
washer operation will be affected.

p. While holding idler lever, reach in and around 

right side of motor and run belt off right side of 
pulley.

q. Using No. 289P4 Spring Hook Tool, unhook 

six module springs from lower edge of outer 
tub. Refer to Figure 53.

Содержание UWT021LA




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды