allen XL5000 OPPOSITE Скачать руководство пользователя страница 25

Страница: 25 / 80

PRODUCT SPECIFICATIONS

XL5000
M02001102EN0319

Power supply

Position the 24 V power supply close to the printing system and connect the output cable to the 24 V

connector of the

printing system. Secure connector by engaging spring or clamp.

Air supply

Position and secure the pressure regulator close to the printing system or in an accessible place where it is easy to
operate.

Connect the pressure regulator air input port to the main air supply line and connect the air output to the printing
system.

Set the pressure regulator to 75psi (~5 bars). Maximum permissible pressure is

6 bars

Control terminal

Use the communication cable to connect the control terminal to the printer.

Tighten the clamping screws (see control terminal

user’s

guide).

Host machine

Use the signal cable to connect the printer to the host machine. See

“

Electrical

installation

”

for connection configura-

tions.

Computer

The

printer can operate connected to a PC and the control terminal at the same time, thereby ensuring maximum flexi-

bility of operation.

You can connect the printing system either by serial or Ethernet connection to your PC (see “

Communication via the

serial interface (RS-232)

” and “

Communication via the Ethernet connection

” for more details).

Encoder (used for continuous mode)

Installation see “

Continuous operation

”

Содержание XL5000 OPPOSITE

















































































Результаты поиска

Содержание XL5000 OPPOSITE

Отзывы:

Похожие инструкции для XL5000 OPPOSITE

Бренды по названию

Популярные бренды

allen XL5000 OPPOSITE, Руководство по эксплуатации

Результаты поиска

Содержание XL5000 OPPOSITE

Отзывы:

Похожие инструкции для XL5000 OPPOSITE

Бренды по названию

Популярные бренды