allen XL5000 OPPOSITE Скачать руководство пользователя страница 39

Страница: 39 / 80

OPERATING

XL5000
M02001102EN0319

ATTENTION

Use of ribbon that is not specified by the manufacturer

The use of ribbons that were not specified by the manufacturer can lead to excessive wear or damage to
the thermal printhead.

▪

Only use ribbons with the width specified by the manufacturer. For information about this, refer to
the

Characteristic

data

▪

Bear in mind that the side coated with color must face towards the product to be printed under
the thermal printhead with correctly loaded ribbon.

NOTE

Ribbon

Observe the permissible ribbon width and the maximum permissible diameter of the ribbon roll for your
thermal printhead type. For information about this, refer to the

Characteristic

data

①

Handle

③

Alignment pin (male on printer)

②

Cassette locking knob

④

Alignment pin (female on cassette)

Description of the ribbon change process:

Step 1: Remove cassette

Unlock the cassette by turning the cassette latch counterclockwise. Move the cassette out of the printer.

Step 2: Removing used ribbon

Remove the used ribbon roll and cardboard sleeve from the ribbon upwind.

①

②

③

④

Содержание XL5000 OPPOSITE

















































































Результаты поиска

Содержание XL5000 OPPOSITE

Отзывы:

Похожие инструкции для XL5000 OPPOSITE

Бренды по названию

Популярные бренды

allen XL5000 OPPOSITE, Руководство по эксплуатации

Результаты поиска

Содержание XL5000 OPPOSITE

Отзывы:

Похожие инструкции для XL5000 OPPOSITE

Бренды по названию

Популярные бренды