allen XL5000 OPPOSITE Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 80

background image

PRODUCT IDENTIFICATION

14

XL5000

M02001102EN0319

1.5.2

EMC Compliance Statements

European Union (EU) Electromagnetic Compatibility Directive Compliance Statement

This product is in conformity with the protection requirements of EU Council Directive 2014/30/EU on the approxima-
tion of the laws of the Member States relating to electromagnetic compatibility.

Federal Communications Commission (FCC) Emissions Compliance Statement

This equipment has been tested and complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device might not cause harmful interference, and (2) this device must accept any interference received, includ-
ing interference that might cause undesired operation.

Warning: Operation of this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at their own expense.

1.5.3

RoHS / WEEE

–

compliance

RoHS

The product complies with the relevant provisions of the RoHS Directive for the European Union.

WEEE Directive Statement for the European Union

WEEE-Reg.-No. DE

84410135

In common with all Electronic and Electrical products this product should not be disposed of in household waste. Alter-
native arrangements may apply in other jurisdictions.

«
...
12
13
14
15
16
...
»

Содержание XL5000 OPPOSITE

















































































Отзывы:

Нет отзывов

Похожие инструкции для XL5000 OPPOSITE

Бренд: Xerox Страницы: 73

Бренд: Xerox Страницы: 2

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 20

Бренд: Oki Страницы: 42

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 13

Бренд: Oce Страницы: 2

Бренд: Oki Страницы: 193

Delta Rostock mini G2 pro

Бренд: Geeetech Страницы: 89

Бренд: IDStation Страницы: 18

Бренд: Gainscha Страницы: 12

Бренд: MIMAKI Страницы: 20

Бренд: Xerox Страницы: 109

Бренд: Paradise POS Страницы: 275

Бренд: Oki Страницы: 204

VERSAJET MP3200 Series

Бренд: Cino Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды