Allen-Bradley PLC-5 MAP/OSI Скачать руководство пользователя страница 7

Страница: 7 / 135

Preface

Allen-Bradley PLC-5 MAP/OSI Software

(Cat. No. 1785-OSI)

P-3

Figure P.1

You Must Have This Equipment Installed Before Using the OSI Software

Allen-Bradley 6200 Software

OSI Network

Allen-Bradley MAP

Station Manager

1785-OSI

Software

IBM PC Compatible/DOS Computer

Allen-Bradley T47 Terminal or

FORCE

BATT

PROC

COMM

PROG

RUN

A B

CH2

CH0

A B

CH1

BATTERY

INSTALLED

PLC-5/40

PROGRAMMABLE

CONTROLLER

PASS

MODE

ACT

BATT

802.4

STATUS

RS-232

BATTERY

INSTALLED

D M Y

OSI

INTERFACE

802.4

INTERFACE

MODEM

The Connector Header

mates the PLC-5 controller

to the OSI coprocessor.

The PLC-5 OSI Coprocessor

Lithium Battery.

OSI Modem

PLC-5 802.4 MAP/OSI Coprocessor

Into an Allen-Bradley 1771 I/O Chassis

series B, install:

- the PLC-5 controller

- the OSI coprocessor

- the P7 power supply

- the modem

Allen-Bradley 6200 software

connects to the PLC-5 controller.

PLC-5/40, -5/60

controller

I - 12405

If you need more information on these products, contact your local
Allen–Bradley integrator or sales office for assistance.

AB Parts

Содержание PLC-5 MAP/OSI








































































































































Результаты поиска

Содержание PLC-5 MAP/OSI

Отзывы:

Allen-Bradley PLC-5 MAP/OSI, Руководство пользователя, Страница: 7 / 135

Результаты поиска

Содержание PLC-5 MAP/OSI

Отзывы: