manualshive.com logo in svg

Allen-Bradley PLC-5 MAP/OSI, Руководство пользователя, Страница: 25 / 135

Поделиться
Скачать
Allen-Bradley PLC-5 MAP/OSI Скачать руководство пользователя страница 25

Chapter 2

The PLC-5 802.4 MAP/OSI Coprocessor

2-7

The OSI coprocessor has a four–position dip switch you can access
without removing any covers.  The switches are labelled 1, 2, 3, and 4 and
are located at the back of the coprocessor.  Above the switches you will see
a small legend that illustrates the ON and OFF position of the switches
(figure 2.5). 

Important: Your OSI coprocessor is shipped with all of its switches in the
OFF position.  If you need to change the switch settings, you must do so
before you install the OSI coprocessor into the chassis.

Figure 2.5

The OSI coprocessor's switches

1. ON = POWERUP IN PARTIALLY OPERATIONAL MODE

2. ON = POWERUP USING A-B COMM DEFAULTS

3. ON = AUTOCLEAR FUNCTION ENABLED

4. RESERVED = MUST BE OFF

ON

OFF

19231

1

4

1

2

3

4

Figure 2.6 provides a larger view of the switches and a description of each
one.

The Switches

AB Parts

Содержание PLC-5 MAP/OSI








































































































































Отзывы:

Нет отзывов