Allen-Bradley PLC-5 MAP/OSI Скачать руководство пользователя страница 26

Страница: 26 / 135

Chapter 2

The PLC-5 802.4 MAP/OSI Coprocessor

2-8

Figure 2.6

A Description of Each OSI Coprocessor Switch

Allows you to select the default mode of operation the

coprocessor enters on power-up or reset.

Fully Operational/Partially Operational Switch

When this switch is:

partially operational mode.

Then the coprocessor:

If you select:

The coprocessor powers

up in:

fully operational mode.

enters fully operation

mode.

enters partially

operational mode.

enters partially

operational mode.

fully operational mode

and there is a valid image

in non-volatile memory
fully operational mode

and there is not a valid

image in non-volatile

memory

partially operational

mode.

Allows you to select the values the coprocessor uses for the MAC layer and

RS-232 port parameters on power-up or reset.

User/Allen–Bradley Communication Defaults Switch

When this

switch is:

The coprocessor powers

up using:

Allen-Bradley

communication default

settings.

user communication default

settings. If no user defaults are

stored, Allen-Bradley

communication defaults are

used.

These settings are the values:

used for the MAC layer and RS-232

port configuration parameters

whenever the coprocessor's

non-volatile memory is reinitialized.

of the MAC layer and RS-232 port

parameters when you edit them via

the Allen-Bradley MAP Station

Manager. The coprocessor uses

these values in place of the

Allen-Bradley communication

defaults (unless this switch is set to

ON).

Allows you to specify whether or not the contents of non-volatile memory will be erased (cleared) when the coprocessor is detached from the PLC-5 controller,

and reattached to a different controller.

Auto Clear Switch

When this

switch is:

Then:

the auto clear function is disabled and you are free to

interchange coprocessors and PLC-5 controllers at anytime

WITHOUT losing the contents of non-volatile memory.
the autoclear function is enabled. The contents of non-volatile

memory will be erased if and only if you complete all of the

following tasks:

Unmate the coprocessor and PLC-5 controller.

Reattach the coprocessor to a different PLC-5 controller.

Install the new mated pair into a chassis and apply power.

Place the coprocessor into fully operational mode.

Why Use the Auto Clear Switch?

Typically, a maintenance engineer can swap a non-functioning

OSI coprocessor with another. A coprocessor, initially mated to a

PLC-5 controller, could later be mated to another. Since the

configuration information follows the OSI coprocessor, that

information may be incorrect for the new PLC-5 controller

location.

It is possible, for example, that some of the MMS named variables

in the first application would match those in the second application

in name, but not in content or meaning. This is a situation where

you may decide to ENABLE the auto clear switch, allowing you to

clear the contents of the coprocessor's non-volatile memory,

even with the coprocessor mated to a new PLC-5 controller.

(Switch 1)

(Switch 2)

(Switch 3)

(Switch 4)

Important:

Keep this switch

OFF. This should be turned on by

authorized Allen-Bradley

personnel only.

OFF

I - 12419

Содержание PLC-5 MAP/OSI








































































































































Результаты поиска

Содержание PLC-5 MAP/OSI

Отзывы:

Allen-Bradley PLC-5 MAP/OSI, Руководство пользователя, Страница: 26 / 135

Результаты поиска

Содержание PLC-5 MAP/OSI

Отзывы: