Allen-Bradley PLC-5 MAP/OSI Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 135

Allen-Bradley PLC-5 MAP/OSI Скачать руководство пользователя страница 24

Chapter 2

The PLC-5 802.4 MAP/OSI Coprocessor

2-6

The OSI coprocessor has five LEDs on the front panel. At power–up, the
LEDs cycle through each of their colors (either red or green) so you can
visually inspect them. Each LED has a specific function. Figure 2.4
provides an overview of each LED.

Figure 2.4

The OSI Coprocessor's LEDs

This LED indicates the overall condition of the

coprocessor.

If this LED is:

Then the coprocessor is:

green

red

functioning properly and has passed all

hardware diagnostics.
faulted and service is required before

normal operation can continue.

Pass/Fail LED

This LED indicates the coprocessor's operating mode.

Mode LED

Mode:

Description:

partially

operational

fully

operational

the coprocessor is waiting for the OSI

protocol software to be downloaded via the

MAP station manager, or has transitioned to

this mode due to a fault while in fully

operational mode.

this is the mode of normal operation where

the coprocessor can perform all

communication functions.

off

flashing

the coprocessor is in partially operational

mode and has a valid image loaded (able

to go fully operational).

the coprocessor is in partially operational

mode and a new image must be loaded in

order to transition to fully operational

mode.

red

the coprocessor has a valid image and

is in fully operational mode.

a diagnostic test failure has occurred. If

the coprocessor has faulted, the pass/fail

LED should also be red (service is

required before normal operation can

continue).

solid

green

solid

red

If this LED is red, this indicates that the batter power is

not sufficient to retain non-volatile memory if power to

the coprocessor is removed. You should replace the

battery with a new one if you want this storage preserved

in the event of a power loss.
Refer to the OSI coprocessor's Installation Data

(publication 1785-2.23 and 1785-2.24) for battery

replacement instructions.

Battery Low LED

This LED indicates the presence of communication

activity in the coprocessor.

Activity LED

If this LED is: Then the coprocessor is:
green
off

receiving or sending messages.

not receiving or sending messages.

The LED:

off

flashing

Indicates:

red

the coprocessor is not ready to

communicate.
the coprocessor is ready to

communicate.

an unrecoverable communications

error has occurred and service is

required.

a recoverable communications error has

occurred, which can possibly be fixed with

reconfiguration

802.4 Status LED

solid red

This LED indicates the status of coprocessor's network

communication.

PASS

PASS

MODE

ACT

BATT

802.4

STATUS

RS-232

solid

green

Then:

If this LED is:

I - 12418

The LEDs

«
...
22
23
24
25
26
...
»

Содержание PLC-5 MAP/OSI








































































































































Отзывы:

Нет отзывов