Allen-Bradley PLC-5 MAP/OSI Скачать руководство пользователя страница 109

Страница: 109 / 135

Communication Layers' Attributes

Appendix D

D-3

The System–Layer attributes control the communication between the OSI
coprocessor and the Allen–Bradley MAP Station Manager.

System-Layer

Parameters:

Description:

Printf_option

When the Allen-Bradley MAP Station Manager terminal is connected directly to the

RS-232 port of the OSI coprocessor, this parameter provides the option of having all

diagnostic information messages that come out from the module ``translated" such

that they can be understood by the Manager.

Printf_enable

This enables the parameter shown above. Dictates whether or not diagnostic

information messages can go out of the RS-232 port.

Pass Through Option

Reserved for future use.

System-Layer Status:

Description:

Current Mode

The current operating mode of the OSI coprocessor (Partially or Fully Operational).

Battery

A value of OK indicates that the OSI coprocessor battery has sufficient power to

retain non-volatile memory.

Firmware Revision:

Revision

The revision number of your OSI coprocessor firmware.

Software Revision:

Revision

The revision number of your OSI coprocessor software.

Switch settings:

This reflects the condition of the OSI coprocessor's four switches (see list below).

Mode After Reset

This switch determines which mode, either Fully or Partially Operational, the OSI

coprocessor attempts to transition to after a system reset or powerup. A value of

OFF is interpreted as a command to Go Fully Operational.

A value of ON is

interpreted as a command to Go Partially Operational.

Communication

Defaults

The OSI coprocessor contains both

Allen-Bradley and user default values. The

Allen-Bradley defaults are stored in read-only memory and the user defaults are

stored in non-volatile read/write memory. This switch determines which default

setting to apply after a system reset or powerup. A value of OFF is interpreted as a

command to use the user defaults. A value of ON is interpreted as a command to

use the Allen-Bradley defaults. See the preceding sections titled

Definition of

Defaults

, for description of user and Allen-Bradley defaults.

Auto Clear

Allows you to specify whether or not the contents of non-volatile memory are to be

erased (cleared) when the coprocessor is detached from the PLC-5 controller (and

re-attached to a different PLC-5 controller). See Chapter 2 of this manual for the

four events that must occur for the auto clear function to work.

Reserved

Reserved and should always be OFF.

Image ID:

File name

The filename is the name of the disk file on the Allen-Bradley MAP Station Manager

that contains the loadable image (software program) that was loaded into this OSI

coprocessor.

Image type

The image type is an integer that represents the type of loadable image in the OSI

coprocessor. This will always be the number 2.

System-Layer Attributes

AB Parts

Содержание PLC-5 MAP/OSI








































































































































Результаты поиска

Содержание PLC-5 MAP/OSI

Отзывы:

Allen-Bradley PLC-5 MAP/OSI, Руководство пользователя, Страница: 109 / 135

Результаты поиска

Содержание PLC-5 MAP/OSI

Отзывы: