Allen-Bradley PLC-5 MAP/OSI Скачать руководство пользователя страница 53

Страница: 53 / 135

Chapter 4

Basic Programming Techniques

4-3

Figure 4.2

Sample Message Instruction

MG9:3

SEND/RECEIVE MESSAGE

Control Block MG9:3

MSG

EN
DN
ER

I - 12421

The procedure for using the PLC–5 programming software is listed below.
You can exit from this procedure at any time by pressing the [ESC] key.

Important: We assume you are familiar with programming Allen–Bradley
PLC controllers using the PLC–5 programming software.

Position the cursor on the rung display where you want to insert the
message instruction.

Press [F10], the edit option. A new set of options appears.

Press [F4], the insert rung option. A new set of options appears.

Press [F4], the insert instruction option. A new set of options
appears.

Press [F10], the others option. A new set of options appears.

Press [F3], the I/O Message option. A new set of options appears.

Press [F5], the MSG option. The following message appears:

Enter Message Control Block address >

AB Parts

Содержание PLC-5 MAP/OSI








































































































































Результаты поиска

Содержание PLC-5 MAP/OSI

Отзывы:

Allen-Bradley PLC-5 MAP/OSI, Руководство пользователя, Страница: 53 / 135

Результаты поиска

Содержание PLC-5 MAP/OSI

Отзывы: