ALL-TEST PRO ATPOL II Скачать руководство пользователя | Manualshive

Страница: 2 / 109

background image

2

The APOL II is designed to comply with part 15, subpart B, of the FCC Rules for a Class A digital
device.

Model ATPOL II is designed to comply with the requirements of IEC61010-1:2001 for a 600V input
rating measurement category IV, pollution degree II, double insulated electronic device.

Model ATPOL II is manufactured for ALL-TEST Pro, LLC in the U.S.A.  The standard warranty period is
12 months from date of purchase unless you have purchased an extended warranty.  We encourage
you to advise us of any defects of design or manufacture of any of our products.  We are dedicated to
your successful use of the product.

There are no user serviceable parts in your ATPOL II meter. Opening the case voids your

warranty and may result in present or future danger to users of the meter. The rechargeable battery
inside is a custom-designed battery pack that is only to be replaced by authorized ALL-TEST Pro, LLC
(ATP) technical service personnel.

Cleaning is to be done by use of a dry or damp piece of cloth. Grease may be removed by light

application of isopropyl (rubbing) alcohol. Avoid the use of solvents, since they may dissolve or
weaken the plastic enclosure. Do not use water or other conductive liquids since they may pose a
safety risk.

Use of this equipment in a manner not specified by ATP can result in injury and voiding of

warranty.

«
1
2
3
4
...
»

Содержание ATPOL II














































































































Отзывы:

Нет отзывов

Похожие инструкции для ATPOL II

Бренд: Parr Instrument Страницы: 110

Бренд: Van Walt Страницы: 2

Бренд: Galileo Страницы: 19

Бренд: Galileo Страницы: 71

Бренд: NanoEnTek Страницы: 4

Бренд: P3 International Страницы: 2

Бренд: Vega Страницы: 28

Бренд: Vega Страницы: 20

Electone B-20CR

Бренд: Yamaha Страницы: 16

Бренд: KROHNE Страницы: 56

Бренд: marposs Страницы: 58

Бренд: Dräger Страницы: 538

Бренд: Motortech Страницы: 142

Бренд: Neogen Страницы: 9

Бренд: Power Measurement Страницы: 20

Бренд: Sensitech Страницы: 2

Бренд: Proteus Страницы: 4

Prosonic S FMU90 PROFIBUS DP

Бренд: Endress+Hauser Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды