Alinco DJ-V57 Скачать руководство пользователя страница 59

Страница: 59 / 72

10.Maintenance and Reference

• When using EDC-36, EDC-37, EDC-43, EDC-146, EDC-147, connect them to the

unit first before turning on the unit.

• EBP-63, 64, 65 and 66 are IPX7-grade water-proof only when correctly attached and

used with DJ-V57.

10.3.1 Microphone/Speaker Cable (EDS-14)

1. Turn off the unit.

2. Turn the plug clockwise until it stops. Check to be

sure it is securely connected.

3. Connect the Microphone/Speaker plugs to the each

jack.

10.3.2 Battery Packs

The battery packs aren't fully charged when shipped.

Please charge the pack completely before use.

Available Battery Packs for DJ-V57:

EBP-63

Li-ion Battery Pack (DC 7.4V 1100mAh)

EBP-64

Li-ion Battery Pack (DC 7.4V 1600mAh)

EBP-65

Ni-MH Battery Pack (DC 7.2V 700mAh)

EBP-66

Ni-MH Battery Pack (DC 7.2V 2000mAh)

Charging Battery Packs

Refer to the chart below for the combination of the proper battery pack and charger.

The

indicates the usable combination, (* hrs) means the approximate time

necessary to full charge the empty pack.

Battery Packs

Chargers

Trickle Charger EDC-143
Rapid Charger EDC-144
Wall Charger EDC-146/147/148

Li-ion Battery Pack

EBP-63

(2hrs)

Ni-MH Battery Pack

EBP-65

(10hrs)
(1.5hrs)
(10hrs)

EBP-64

(3hrs)

EBP-66

(14hrs)
(3.5hrs)
(30hrs)

○

■

Plug

Microphone jack
(

2.5)

Speaker jack
(

3.5)

Содержание DJ-V57









































































Результаты поиска

Содержание DJ-V57

Отзывы:

Бренды по названию

Популярные бренды

Alinco DJ-V57, Инструкция по эксплуатации

Результаты поиска

Содержание DJ-V57

Отзывы:

Бренды по названию

Популярные бренды