Alinco DJ-V57 Скачать руководство пользователя страница 50

Страница: 50 / 72

8.Set Mode

8.3.13 Menu 13 DTMF WAIT Time

Use this parameter to delay the time to start transmitting the DTMF tones in Auto

Dialer operation. The initial setting is 100ms.

1. DWT-01 is displayed on the LCD.

2. Rotate the dial to change the DTMF wait time setting.

8.3.14 Menu 14 DTMF First Digit Burst Time

It often happens that the radios fail to receive the very beginning instant of each

communication due to squelch/TSQ/DCS etc. By setting the burst time of the first

digit longer, the risk to miss the first DTMF tone will decrease.

1. DB-60 is displayed on the LCD.

2. Rotate the dial to select the initial-character burst time.

8.3.15 Menu 15 DTMF Burst Time

This parameter determines the length of DTMF tones.

1. DP-60 is displayed on the LCD.

2. Rotate the dial to change the DTMF burst time setting.

8.3.16 Menu 16 DTMF Pause Time

This parameter determines the length of pause time between the tones.

1. DP-60 is displayed on the LCD.

2. Rotate the dial to change the DTMF pause time setting.

DP-20

-----

DP-100

-----

DP-200

(unit: ms)

DB-20

-----

DB-100

-----

DB-200

(unit: ms)

DF-20

-----

DF-100

-----

DF-200

(unit: ms)

DWT-01

-----

DWT-05

-----

DWT-10

(unit: 100ms)

NOTE:

The following 4 menus explain the Auto Dialer DTMF tone parameters. Please
refer to the chart at the end for details.

Содержание DJ-V57









































































Результаты поиска

Содержание DJ-V57

Отзывы:

Бренды по названию

Популярные бренды

Alinco DJ-V57, Инструкция по эксплуатации

Результаты поиска

Содержание DJ-V57

Отзывы:

Бренды по названию

Популярные бренды