Alinco DJ-V57 Скачать руководство пользователя страница 3

Страница: 3 / 72

NOTICE / Compliance Information Statement

Conformity Information

Alinco, Inc. Electronics Division hereby declare on our sole responsibility that the

product(s) listed below comply the essential requirements of the Directive 1999/5/EC,

The council of 3/9/99 on Radio Equipment and Telecommunication Terminal

Equipment and the mutual recognition of their conformity and with the provisions of

Annex, after having performed the required measurements at Notified Bodies per

Standards, and relative certificate(s) or document(s) can be reviewed at http://www.

alinco. com/Ce/

DJ-V57E FM amateur radio handheld transceiver

144.000~145.995MHz / 430.000~439.995MHz

This device is authorized for use in all EU and EFTA member states. An operator's

license is required for this device.

translated or transcribed in any form or by any means without the prior written

permission of Alinco. Inc., Osaka, Japan. English edition Printed in Japan.

Check with your local waste officials for details on recycling or proper disposal in

your area.

2200

Содержание DJ-V57









































































Результаты поиска

Содержание DJ-V57

Отзывы:

Бренды по названию

Популярные бренды

Alinco DJ-V57, Инструкция по эксплуатации

Результаты поиска

Содержание DJ-V57

Отзывы:

Бренды по названию

Популярные бренды