Alinco DJ-V57 Скачать руководство пользователя страница 11

Страница: 11 / 72

Warning

Lightning

Any person is not safe outdoor during thunderstorm and lightning. This condition is

getting worse if somebody keeps a hand-held radio; chances of being hit by lightning are

doubled since lightning may hit a radio antenna as well. At this time, there is no hand-

held radio having any kind of protection against lightning current (which is higher than

10 kA.). Note also that no car provides adequate protection of its passengers or drivers

against lightning as well. Therefore, Alinco will not take responsibility for any danger

associated with using its hand-held radios outdoor or inside the car during lightning.

Limited Power Source

Please note that the transceiver enclosure only provides mechanical protection of its

internal parts; it will not contain a fire within the device if the fire starts under certain

fault conditions. Alinco will not take responsibility for any fire hazard associated with

powering the transceiver or charging its batteries using a power source which does not

belong to the limited power sources in the meaning of EN 60950-1. Excluded from

possible use with the transceiver are most car cigarette lighters and some DC

(AC/DC) power supplies. Make sure that the power supply used with the transceiver

is a limited power source.

Water-registant

The IPX7 designation provides for limited waterproofing of the radio. The

specifications are immersion in one meter (approx 3ft) of still sweet water for up to 30

minutes. This compatibility is factory guaranteed for a period of one year provided all

the jack covers are securely in place, any accessories connected must be genuine

Alinco water-proof accessories and the radio has not been disassembled by the

customer. The factory has tested and made the equipment compatible to IPX7

certification during engineering. However, please understand that this equipment is

NOT certified IPX7 compliant but is designed to remain operational when used in

rain, severe weather or in accidental cases of dropping it in water when used in

extreme conditions and is in no way stating that you should attempt use the radio

under water or submerge the radio for cleaning. Warranty will not cover radios that

are water / salt damage due to negligence or misuse of the product.

Содержание DJ-V57









































































Результаты поиска

Содержание DJ-V57

Отзывы:

Бренды по названию

Популярные бренды

Alinco DJ-V57, Инструкция по эксплуатации

Результаты поиска

Содержание DJ-V57

Отзывы:

Бренды по названию

Популярные бренды