manualshive.com logo in svg

Alinco DJ-V57, Инструкция по эксплуатации

Поделиться
Скачать
Alinco DJ-V57 Скачать руководство пользователя страница 18

2.Accessories

2

18

2.1.5 Prevent Short Circuiting the Battery Pack

Be extra cautious when carrying the rechargeable battery pack; short circuiting will

produce surge current possibly resulting in fire.

2.1.6 Battery-Level Icon

During the operation, a black battery icon indicates

that the battery-level is in usable range.  When it

turns to empty, please charge the pack or replace the

cells with new ones.

Battery-level icon

The battery is in usable 
condition.
Battery-level is low.  
Replace or charge the pack.

DON'T carry with 
metals of any type, e.g. 
chains.

DON'T carry the battery 
pack inside bags made 
of conductive materials.

DON'T place in the 
proximity of metals or 
conductives, e.g. nails, 
chains.

Do enclose inside a non-conductive enclosure. (bags or 
handkerchief made only of non-conductive material)

Do protect by spreading 
a non-conductive sheet 
on a flat surface.

Содержание DJ-V57









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды