AJS 350 1954 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 96

AJS 350 1954 Скачать руководство пользователя страница 91

1

1

2

1

1

1

1

1

1

1

1

2

1

1

1

1

1

1

1

017253

017114

017007

017248

011188

017256

017246

017249

017252

017254

018178

017052

017053

017251

015023

017257

018055

018153

018657

Tool bag.

Tyre inflator.

Tyre lever.

Pliers.

Gudgeon pin circlip pliers.

Screwdriver.

Grease gun.

Adjustable wrench,

Sparking plug box spanner and tommy bar.

Dynamo spanner and clutch spring nut key.

Double end spanner, 1·010 in. by 1·200 in.

Double end spanner. Small.

Double end spanner. Large.

Contact point spanner and gauge (Touring).

Contact point spanner and gauge. (Competition)

Double end spanner.

Handlebar clip screw key.

Single spanner for petrol tap.

Key for fork crown clamp screw (not illustrated.)

TOOLS AND SPECIAL EQUIPMENT

TOOLS

The standard tool kit, issued with each new machine, contains :

OPTIONAL EQUIPMENT

The  following  Items  of  optional  equipment  are  available.  They  are  described  and
priced  in  the  Spares  List.
Stop  rear  light.
Air  cleaner.
Mudguard  type  pillion  seat  (Rigid  Frame  Models).
Pillion  footrests,  bolted  on,  to fold  up  when  not  in  use  and  specially designed for  these
machines,  (Not  on  competition).
Detachable  luggage  carrier.  (Not  on  competition).
Timing  disc  015955.  A circular  timing  disc,  graduated  in  degrees  and  made  of ivorine.
A  very  useful  device.
Valve  holder,  for  valve  grinding.  Part  number 017482.
Valve spring  compressor.  Part  number 018276.  (See  page  28).
Pannier frames and  bags for spring frame and  rigid  models.

SPARES LIST

An illustrated and priced spares list is available at a cost of 2/6 post free. (See page 28).

GASKET SETS

For convenience  in ordering, standard sets of engine  washers  and  gaskets as well  as the
washers  used  in  the  petrol  and  oil  feed  systems  are  stocked.  Full  details  of  contents
and  prices are included  In the Spares  List.

89

«
...
89
90
91
92
93
...
»

Содержание 350 1954

































































































Отзывы:

Нет отзывов