AJS 350 1954 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 96

AJS 350 1954 Скачать руководство пользователя страница 74

In the following five paragraphs are particulars of failures and troubles that can occur,
together with the probable reasons. These troubles are arranged in the order of their
probability.

TRACING TROUBLES

Engine fails to start, or is difficult to start, may be due to

:

Water on  high-tension  pick-up.
Moisture on sparking  plug.
Oiled  up, or fouled,  sparking  plug.
Throttle  opening  too  large.
Pilot  jet  choked.
Air  lever  in  open  position,  or  bad  air  leak  at  carburetter flange.
Lack of fuel  because of insufficient  Flooding  (cold  only).
Lack of fuel  because of pipe,  or  tap, obstruction.
Excessive  flooding  of carburetter  (with  hot  engine  only).
Stuck  up  engine  valve.
Weak,  or  broken,  valve  spring.
Valve  not seating  properly.
Contact  points  dirty.
Incorrect  contact  point  gap.

Engine misses fire may be due to :

Defective, or oiled,  sparking  plug.
Incorrect  contact  point  gap,
Contact  breaker  points  loose.
Rocker  adjustment  incorrect.
Oil  on  contact  breaker  points.
Defective  sparking  plug wire.
Partially  obstructed  petrol  supply.

Loss of power may be due to :

Faulty sparking  plug,
Lack  of oil  in  tank.
Weak, or  broken,  valve spring.
Sticky  valve  stem.
Valve  not seating  properly.
Brakes adjusted  too  closely.
Badly fitting,  or  broken,  piston  rings.
Punctured  carburetter  float.
Engine carbonised.
Choked  silencer.

USEFUL INFORMATION

72

«
...
72
73
74
75
76
...
»

Содержание 350 1954

































































































Отзывы:

Нет отзывов