AJS 350 1954 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 96

AJS 350 1954 Скачать руководство пользователя страница 45

TO REMOVE FRONT CHAINCASE AN D CLUTCH ASSEMBLY

To remove outer half of front chaincase

Place tray under chaincase to catch oil.

Remove left side footrest arm.

Remove screw binding chaincase metal band at its rear.

Remove metal band.

Remove endless rubber band.

Remove nut and washer, in centre of chaincase front.

Take away outer half of chaincase

To remove front driving chain and clutch assembly complete

Engage top gear, apply rear brake, and unscrew engine sprocket nut,

Unscrew the nuts retaining the clutch springs, using end of spanner Part No. 017254.

Take away the clutch spring pressure plate with the clutch springs and clutch spring cups
and flatten the turned up part of the lock plate that is under the large central nut.

Remove front chain connecting link and take away chain.

Engage top gear, apply rear brake, and unscrew nut retaining the clutch centre to the
gear box mainshaft sleeve.

Remove the lockplate and plain washer from gear box mainshaft.

Remove complete clutch assembly by pulling it away, as one unit from gear box mainshaft.

Take  care  not  to  lose  any  of the  twenty-four clutch  sprocket  bearing  rollers  which  may
be displaced  when  the clutch centre and  sprocket assembly is withdrawn from the main-
shaft.  The clutch  centre  is  a sliding  fit  on  the  mainshaft sleeve  and  an  extractor should
not be required.

To remove dynamo chain and back half of chaincase

Remove the spring lock ring on dynamo sprocket retaining nut.

Take away lock washer surrounding dynamo sprocket nut.

Apply spanner  (017254,  included  in  tool  kit)  to  the two flats  on  the  back  of the  dynamo
sprocket  and,  holding  same,  unscrew  the  nut  retaining the  dynamo sprocket.  Holding
sprocket thus  relieves the  dynamo shaft of  bending  strain.

Release dynamo sprocket with suitable extractor.

Take away, as one assembly, the dynamo sprocket, dynamo chain and engine shock
absorber assembly. (The dynamo chain is " endless.")

Straighten tabs on lock washers under the three bolts retaining the back half of chaincase
to the boss on the crankcase and remove the three bolts.

Remove the long headed bolt (under battery carrier) fixing rear chain guard to front
chaincase.

Remove wide nut and washer on centre fixing bolt, when back half of chaincase can be
taken away.

43

«
...
43
44
45
46
47
...
»

Содержание 350 1954

































































































Отзывы:

Нет отзывов