AJS 350 1954 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 96

AJS 350 1954 Скачать руководство пользователя страница 64

TO REMOVE REAR WHEEL

(Rigid Frame Models)

Place  machine on  rear stand.
Disconnect  rear  lamp wire  at  connection  near  rear wheel  spindle.
Disconnect  speedometer  driving  cable.  (Unscrew  gland  nut  on  cable.)
Disconnect  rear  chain  connecting  link.  (Allow  chain  to  hang  clear  of  the  rear  wheel
sprocket  without  becoming  disengaged  from  the  gear  box  small  sprocket.)  Engage  a
gear  to  prevent  sprocket  revolving.
Slacken  the  two  bolts  securing  rear  portion  of  rear  mudguard  to its front  portion.
Loosen  nut  and  washer  from  bolt  securing  mudguard  side  bridge  and  tool  box  stay  to
tubular  stay.
Remove  adjusting  nut  from  rear  brake  rod.
Slacken  the  two  nuts  (unscrew about four  turns)  retaining  the  rear  mudguard  side stays
to  their  studs.
Slacken  the  two  nuts an  the  rear  wheel  spindle.
Remove the  rear  portion  of the  rear  mudguard,  with  its  stays,  leaving tool  box and  stay
In  position.
Remove  the  rear  wheel  from  the  fork  ends  by  twisting  It  sideways  to  release and  clear
the  rear  brake  cover  plate  anchor  bolt and  then  withdrawing  it  to  the  rear.
Re-fit  in  the  reverse  order  but,  before  finally  tightening  the  rear  wheel  spindle  nuts,
ensure  the  speedometer gear  box  is  so  positioned  that  the  speedometer  driving  cable
can  be correctly  replaced.
When  the  wheel  alignment  is  correct  a  piece  of thin  string  stretched  taut  across  both
wheels,  about four inches from,  and  parallel  to,  the ground,  should  just  touch  each  tyre
at  both  sides  of the  wheel  centres.
Alternatively, a straight wooden  batten, about five feet long,  is  handy to use for checking
wheel  alignment.  This  should  be applied,  as  in  the case of string,  parallel to and  about
four  inches  from  the ground.
NOTE—Always check the  rear chain  tension and  the rear brake adjustment after  making

an alteration to the rear wheel position.

TO RE-FIT REAR WHEEL

(Spring Frame Model)

Reverse  the  removal  procedure,  see  that the speedometer  drive  dogs  are  engaged,  but
leave  the  tightening  of  the  nut  that  locates  the  speedometer  gear  box  for  the  final
operation,  i.e..  after  the  speedometer  cable  has  been  re-connected  and  the  exterior
axle  nuts  have  been  tightened.  (This  also  applies  to  Rigid  Frame  Models.)

1.

2.

REAR BRAKE COVER

PLATE.

BOLT,

ANCHORING

COVER

PLATE

TO

REAR FRAME.

Illustration 20

62

«
...
62
63
64
65
66
...
»

Содержание 350 1954

































































































Отзывы:

Нет отзывов