AJS 350 1954 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 96

AJS 350 1954 Скачать руководство пользователя страница 70

Centralise brake shoes, Front or Rear, by :

Ensure the nut securing the cover plate and also the fulcrum stud nut (front only) are
slightly slacked off.

Place on the brake expander lever a tubular spanner (to increase the leverage}, and, while
maintaining pressure on the tubular spanner (to expand fully the brake shoes), fully
tighten the spindle nut binding the cover plate to the spindle and also the nut on
fulcrum stud,

FRONT BRAKE ADJUSTMENT

Major  adjustment  of  the  front
brake shoes  is  made on  the  brake
thrust  pins,  by  fitting  packing
washers under the pins, as already
described.

Minor  adjustment  of  the  front
brake  shoes  is  made  by  altering
the  position  of  the  brake  cable
adjuster  on  the  fork  assembly.
Unscrew  the  adjuster  to  " take
up  "  the front  brake.

The adjuster is locked in position
by a nut.

Adjust front brake by :

Place machine on both stands.

Slacken lock nut on cable adjuster.

Unscrew the cable adjuster till, by
rotating  the front wheel,  it can  be
felt  the  brake  shoes  are  just
touching  the  brake  drum.

Then  screw  back the  adjuster two
complete  turns  and  tighten  the
lock  nut.

Illustration 23

Showing  front  brake
cable  adjuster  thread
exhausted,  indicating
brake  shoe  thrust pin
a d j u s t m e n t

i s

necessary.

REAR BRAKE ADJUSTMENT

Major adjustment of the rear brake shoes is made on the brake thrust pins, by fitting
packing washers under the pins, as already described.

Minor  adjustment of the  rear  brake  shoes  is  made by  altering  the  position, on  the  brake
rod,  of  the  knurled  adjusting  nut.  Screw  the  nut  further  on  the  rod  to  " take  up  "
the  rear  brake.

68

«
...
68
69
70
71
72
...
»

Содержание 350 1954

































































































Отзывы:

Нет отзывов