AJS 350 1954 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 96

AJS 350 1954 Скачать руководство пользователя страница 67

Illustration 22

Showing  exploded  view  of hub bearing  components  in  the  order  of
assembly.  Upper  part  is that of front  bearings.  (Rigid  and  Spring
Frame  Models).  Lower part  is  that of rear  bearings (Spring Frame

Model only)

(Rigid Frame Models Identical except for items 28 to 32)

1
2

3
4

5

6

7

8

9

10

11

12
13

14

15

16

17

18

CIRCLIP.

WASHER, METAL, OUTSIDE OIL SEAL.

OIL SEAL.
SPACING COLLAR, ENCIRCLING OIL SEAL.

WASHER, METAL, BETWEEN OIL SEAL
AND TAPER BEARING.

OUTER RACES (2 OFF). CENTRE SPINDLE.

ROLLERS IN CAGES (2 SETS),

THESE

ARE N O T SUPPLIED SEPARATELY.

ALSO, ROLLERS ARE N O T SUPPLIED

SEPARATELY.

WASHER, METAL, BETWEEN OIl SEAL
AND TAPER BEARING.

OIL SEAL.
CUP, HOUSING, FOR OIL SEAL.

ADJUSTING RING.
LOCK NUT, FOR ADJUSTING RING.

CIRCLIP.

WASHER, METAL. OUTSIDE OIL SEAL.

OIL SEAL.

SPACING COLLAR. ENCIRCLING OIL SEAL.

WASHER,  METAL,  BETWEEN  OIL  SEAL
AND  SPACER.
SPACER,  BETWEEN  OIL  SEAL  WASHER
AND  TAPER  BEARING.
TAPER  BEARING  (OUTER  CUP,  CAGE  FOR
ROLLERS  AND  ROLLERS)

THESE ARE

N O T SUPPLIED SEPARATELY.

ALSO

ROLLERS

ARE

N O T

SUPPLIED

SEPARATELY.

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

SPACER, BETWEEN BEARINGS.

TAPER BEARING (OUTER CUP, CAGE FOR
ROLLERS AND ROLLERS).

THESE ARE

N O T SUPPLIED SEPARATELY.

ALSO

ROLLERS

ARE

NOT

SUPPLIED

SEPARATELY.

SPACER BETWEEN OIL SEAL WASHER
AND TAPER BEARING.

WASHER, METAL, BETWEEN OIL SEAL
A N D SPACER.

OIL SEAL.
CUP, HOUSING. FOR OIL SEAL.

ADJUSTING RING.

LOCK NUT, FOR ADJUSTING RING.

NUT, EXTERNAL, FOR REAR WHEEL
SPINDLE.

BUSH, FOR REAR WHEEL SPINDLE (FITS
IN FORK END).

KEYWAY,

TO

ACCOMMODATE

KEY

LOCKING CAM TO REAR WHEEL SPINDLE.

REAR WHEEL SOLID CENTRE SPINDLE.

KEYWAY,

TO

ACCOMMODATE

KEY

LOCKING CAM TO REAR WHEEL SPINDLE.

BUSH, FOR REAR WHEEL SPINDLE (FITS
IN FORK END).

NUT, EXTERNAL, FOR REAR WHEEL
SPINDLE.

65

«
...
65
66
67
68
69
...
»

Содержание 350 1954

































































































Отзывы:

Нет отзывов