AJS 350 1954 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 96

AJS 350 1954 Скачать руководство пользователя страница 21

GEAR BOX LUBRICATION

Use one of the grades of Oils specified. In no circumstances must heavy grease be used.

Lubricant is inserted through the filler cap orifice mounted on top edge of kick-starter
case cover.

The gear box must not be entirely filled with oil, and, under normal conditions, the
addition of two fluid ounces of oil every 1,000 miles will be sufficient.

Excessive oil will cause leakage.

A  screwed  drain  plug  in  gear  box  shell,  low  down  at  rear,  facilitates  gear  box  flushing
and  change  of  lubricant.  An oil  level  plug,  adjacent to  K-S spindle,  indicates maximum
permissible  oil  level  (content  I  pint).

HUB LUBRICATION

Keep  hubs  packed  with  grease.  This  prevents  entry of water  and dirt.  Grease  nipples
in  centre of rear hub  and  side  of front hub.  Inject  small  quantity of grease.  Excessive
grease  may  impair  efficiency  of  brakes.

CHAIN LUBRICATION

Front driving chain and dynamo chain run in oil bath. (Front chaincase.) Use engine
oil. Maintain level to height of the inspection cap opening,

Oil in front chaincase also lubricates the engine shock absorber. Transmission harshness
generally Indicates level of oil in chaincase is too low.

Remove chaincase inspection cap each week, Inspect level of oil, top-up as necessary.

To remove inspection cap :—

Unscrew knurled screw about four turns.

Slide cap sideways, till the back plate can be slipped through the opening, and take away
the complete cap assembly.

When replacing inspection cap, centralise cork washer and then fully tighten knurled
screw. Essential this is kept tight otherwise cap assembly will be lost.

Rear  driving  chain  should  be  removed  for  lubrication.  Clean  chain  in  paraffin,  drain
and  wipe.  Immerse  in  bath  of molten  tallow  for  preference,  leave for several  minutes,
remove  and  allow  excess  lubricant to  drain off and then  replace on machine.  Engine oil
is  a  poor substitute for tallow and,  if used,  chain  should  be  allowed  to  soak  for  several
hours  to  ensure  penetration  to  all  joints.

Lubricate rear chain every three thousand miles in Summer and every thousand miles in
Winter.

Magneto chain runs in case packed with grease.

BRAKE EXPANDER LUBRICATION

Grease nipple on each brake expander bush. (One on each brake cover plate.) Use
grease sparingly. Excessive grease may impair efficiency of brakes.

19

«
...
19
20
21
22
23
...
»

Содержание 350 1954

































































































Отзывы:

Нет отзывов