AJA BRIDGE LIVE Скачать руководство пользователя страница 82

Страница: 82 / 139

BRIDGE LIVE Video I/O and Streaming Appliance v1.12 82 www.aja.com

• 23.976 to 24.00,
• 59.94i to 60p

NOTE: You can choose from only two different frame rate (fps) options on the output -

either (i) same as the source, or (ii) halved in rate.

Wrap Captions

The H.264 video codec supports wrapping closed captions. These are available to

be selected and wrapped to output in the video elementary stream only if they

are detected in the source SDI metadata stream as CEA 608 or CEA 708.

Output PID

In general, each elementary stream or table in MPEG-TS is identified by a packet

Identifier. You can specify the PID for your output MPEG-TS. Otherwise it defaults

to the source's PID.

Output Stream Audio Configuration Options

While configuring the output stream, you can choose which transmitted audio or

metadata channels you wish to include. The configurator is shown in Figure 125.

Figure 126. Audio Mapping

Cloning Output Audio Streams

If you need multiple similar output audio streams within one Audio Mapping, you

can clone an output audio stream that you have created earlier.

Содержание BRIDGE LIVE












































































































































Результаты поиска

Содержание BRIDGE LIVE

Отзывы:

Бренды по названию

Популярные бренды

AJA BRIDGE LIVE, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BRIDGE LIVE

Отзывы:

Бренды по названию

Популярные бренды