AJA BRIDGE LIVE Скачать руководство пользователя страница 41

Страница: 41 / 139

BRIDGE LIVE Video I/O and Streaming Appliance v1.12 41 www.aja.com

Selecting the Input Stream Source (JPEG 2000 Channel)

Figure 44. Input stream source selection

For the Input stream configuration options, make selections for Type, IP address,

Port, Ethernet card. In this example, the following selections were made:

• Type: RTP/UDP
• IP address: Enter the IP address for the Ethernet card that is receiving the JPEG

2000 signal. Or set it to 0.0.0.0 (default). BRIDGE LIVE will interpret 0.0.0.0 as

being equivalent to entering the IP address of the Ethernet card.

• Source IP filter: Only multicast traffic originating from the specified IP address

will be received.

•  Port: 5050
•  Ethernet card: Ethernet card 1
•  Compliance with: Auto-detected

Auto-Detecting Video Streams

Click Start Detecting Input.
The Input stream configuration options column updates to show a new heading

called "Auto-detected video streams."

Figure 45. New heading displays called "Auto-detected video streams"

Beneath the heading, what is shown is "Video #1: JPEG2000 1920x1080p @59.94Hz

4:2:2 10-bit.
Click the signal that is listed. The Input stream video configuration options

section expands and is auto-populated with the auto-detected video stream

properties.

Содержание BRIDGE LIVE












































































































































Результаты поиска

Содержание BRIDGE LIVE

Отзывы:

Бренды по названию

Популярные бренды

AJA BRIDGE LIVE, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BRIDGE LIVE

Отзывы:

Бренды по названию

Популярные бренды