manualshive.com logo in svg

AirLive IGR-842PoE, Руководство пользователя

Поделиться
Скачать
AirLive IGR-842PoE Скачать руководство пользователя страница 282

6. 

Web Management: Diagnostics of IGR-842POE

 

 

277 

AirLive  IGR-842POE  User  Manual 

2.  Ping Length:   

The payload size of the ICMP packet. Values range from 2 bytes to 1452 bytes. 

3.  Ping Count:   

The count of the ICMP packet. Values range from 1 time to 60 times. 

4.  Ping Interval:   

The interval of the ICMP packet. Values range from 0 second to 30 seconds. 

5.  Egress Interface (only for IPv6):   

The VLAN ID (VID) of the specific egress IPv6 interface which ICMP packet goes. 

The given VID ranges from 1 to 4094 and will be effective only when the 
corresponding IPv6 interface is valid. When the egress interface is not given, 
PING6 finds the best match interface for destination. Do not specify egress 
interface for loopback address. Do specify egress interface for link-local or 
multicast address. 

Button : 

Start

 – Click to start transmitting ICMP packets.

   

New Ping

 –Click to re-start diagnostics with PING. 

 

6.3 VeriPHY 

Press “Start” to run the diagnostics. This will take approximately 5 seconds. If all ports are 
selected, this can take approximately 15 seconds. When completed, the page refreshes 
automatically, and you can view the cable diagnostics results in the cable status table. Note 
that VeriPHY is only accurate for cables of length 7 - 140 meters. 10 and 100 Mbps ports 
will be linked down while running VeriPHY. Therefore, running VeriPHY on a 10 or 100 
Mbps management port will cause the switch to stop responding until VeriPHY is complete. 
 

Web interface   

To configure VeriPHY in the web interface: 

1.  Click Diagnostics, VeriPHY. 

Содержание IGR-842PoE












































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды