AirLive IGR-842PoE Скачать руководство пользователя страница 280

Страница: 280 / 299

Web Management: Diagnostics of IGR-842POE

275

AirLive IGR-842POE User Manual

Web Management:

Diagnostics of

IGR-842POE

6.1 Ping

This page allows you to issue ICMP PING packets to troubleshoot IP connectivity issues

Web interface

To configure Ping in the web interface:

1. Click Diagnostics, Ping.

Parameter description:

1. IP Address:

The destination IP Address.

2. Ping Length:

The payload size of the ICMP packet. Values range from 2 bytes to 1452 bytes.

3. Ping Count:

The count of the ICMP packet. Values range from 1 time to 60 times.

4. Ping Interval:

The interval of the ICMP packet. Values range from 0 second to 30 seconds.

Содержание IGR-842PoE












































































































































































































































































































Результаты поиска

Содержание IGR-842PoE

Отзывы:

Бренды по названию

Популярные бренды

AirLive IGR-842PoE, Руководство пользователя

Результаты поиска

Содержание IGR-842PoE

Отзывы:

Бренды по названию

Популярные бренды