manualshive.com logo in svg

AirLive IGR-842PoE, Руководство пользователя

Поделиться
Скачать
AirLive IGR-842PoE Скачать руководство пользователя страница 265

5. 

Web Management: Monitor of IGR-842POE

 

 
 
 

 

AirLive IGR-842POE User Manual 

260 

7.  VLAN ID:   

VLAN ID is the VLAN identifier (VID) for the port as defined in IEEE 802.1Q-2003. 
A value of 1 through 4094 is used to define a valid VLAN ID. A value of 0 (Priority 
Tagged) is used if the device is using priority tagged frames as defined by IEEE 
802.1Q-2003, meaning that only the IEEE 802.1D priority level is significant and 
the default PVID of the ingress port is used instead. 

8.  Priority:   

Priority is the Layer 2 priority to be used for the specified application type. One of 
the eight priority levels (0 through 7). 

9.  DSCP:   

DSCP is the DSCP value to be used to provide Diffserv node behavior for the 
specified application type as defined in IETF RFC 2474. Contain one of 64 code 
point values (0 through 63). 

10.  Auto-negotiation:   

Auto-negotiation identifies if MAC/PHY auto-negotiation is supported by the link 
partner. 

11.  Auto-negotiation status:   

Auto-negotiation status identifies if auto-negotiation is currently enabled at the link 
partner. If Auto-negotiation is supported and Auto-negotiation status is disabled, 
the 802.3 PMD operating mode will be determined the operational MAU type field 
value rather than by auto-negotiation. 

12.  Auto-negotiation Capabilities:   

Capabilities   
Auto-negotiation Capabilities shows the link partners MAC/PHY capabilities. 

Button : 

Auto-Refresh

  –  Check this box to refresh the page automatically. Automatic 

refresh occurs every 3 seconds.

   

Refresh

 – Click to refresh the page. 

 
5.11.3.  EEE 

By using EEE power savings can be achieved at the expense of traffic latency. This latency 
occurs due to that the circuits EEE turn off to save power, need time to boot up before 
sending traffic over the link. This time is called "wakeup time". To achieve minimal latency, 
devices can use LLDP to exchange information about their respective tx and rx "wakeup 
time ", as a way to agree upon the minimum wakeup time they need. 
This page provides an overview of EEE information exchanged by LLDP. 
 

Web interface   

To configure LLDP in the web interface: 

1.  Click Monitor, LLDP, EEE. 

2.  If you want to auto-refresh the information then you  need to evoke the 

“Auto-refresh”. 

Содержание IGR-842PoE












































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды