manualshive.com logo in svg

Air Liquide MONNAL T75, Руководство пользователя

Поделиться
Скачать
Air Liquide MONNAL T75 Скачать руководство пользователя страница 113

12 Technical description

Main power supply

Main fuses (x2)

T 3,15 A L, 250 V

Electrical class

I

Type

A

Leak current

IEC 60601-1 compliant

Protection following a loss of power

Continuous audible alarm and patient vented to

atmosphere

Internal battery (Air Liquide ref. KY633300)

Type

NiMh
Rated voltage: 24 V
Rated capacity 2X4500 mAh

Battery capacity (new and charged battery) with

the standard ADULT configuration

3 h typical
Ambient temperature: 25°C

Charging time (h)

10 h typical (according to environmental condi-

tions)

Isolation

Separation from the power supply

To electrically separate the 

Monnal T75

 from the

power supply, disconnect the flexible power ca-

ble.

12.4.3.3 Electromagnetic Compatibility

All of the information set out below was obtained from the normative requirements to which the manu-

facturers of electro-medical devices are subject, within the meaning of standard IEC 60601-1-2 Ed4.
The medical device is compliant with the electromagnetic compatibility standards in force; neverthe-

less the user shall ensure that any electromagnetic interference does not create an additional risk,

such as radio-frequency transmitters or other electronic devices.
In this section you will find the information required to ensure that the installation and putting into op-

eration of your medical device is carried out under the best possible conditions in terms of electro-

magnetic compatibility. The various leads attached to the medical device must be separated from

each other.
Certain types of telecommunications mobile devices such as mobile phones may interfere with the

medical device. The recommended separation distances in this section must therefore be strictly ob-

served.
The medical device must not be used in close proximity to other equipment or placed on top of other

equipment. If this cannot be avoided, its operation under the conditions of use must be checked be-

forehand. The use of accessories other than those specified or sold by 

Air Liquide Medical Systems 

as

replacement parts may have the consequence of increasing the emissions or decreasing the immunity

of the medical device.

113

Содержание MONNAL T75











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды