AIC N 280 FS Скачать руководство пользователя страница 27

Страница: 27 / 84

I-27

B-070343_EN • B

roduct

nstallatIon

Safety Instructions for the Installation

The appliance must be in-

stalled in a dry and protect-

ed area, with an ambient

temperature comprised be-

tween 0 and 45°C.

Make sure to protect the appliance and

the heating system against freezing.

The appliance must be installed to en-

sure easy access at all times.

Use an appropriate means of handling,

suitable to the appliance size and weight.

Floor-standing appliances must be in-

stalled on a level base and wall-hung

appliances, on a vertically plumb sup-

port. Material used for base and sup-

port must have suffi cient strength to

support the appliance weight, water

included.

Make sure that the appliance is installed

with a suffi cient height to allow the con-

densates to fl ow to the sewer, and/or

allow the installation of a condensate

neutralisation system (as required).

When lifting, moving or installing the

appliance, be careful not to drop it.

Once in position, make sure that the

appliance is secured.

Install all pipes and ducts without stress

to prevent any leaks from occurring.

When the appliance is con-

nected to the electrical net-

work, it must be earthed.

Make sure that a fuse or circuit breaker

of the recommended rating is installed

outside the appliance, so as to be able

to shut the power down.

Do not touch the appliance with any

wet body parts when it is supplied with

electrical power.

Before performing any operation on

the electrical circuit, isolate the electri-

cal supply of the appliance through the

external power-cutting device (fuse,

circuit breaker, etc.)

All connections (electrical, fl ue pipe,

hydraulic, gas) must be carried out

in accordance with current standards

and regulations in force.

If the appliance is installed against a wall

made of heat-sensitive material, such as

wood, a suitable insulation must be pro-

vided by the installer between the appli-

ance and the wall surface.

Comply with the clearance dimensions

provided in this manual, to prevent any

hot part of the appliance from being

too close to the walls or any combus-

tible material.

Make sure to maintain a safe distance

of 200 mm from fl ammable materials;

the boiler room may not be used as a

storage location for material.

Do not store any fl ammable, corrosive or

explosive products next to the appliance.

Do not install the appliance in a loca-

tion where chemical vapours or dust are

present in the ambient or combustion air.

If the appliance is used on professional

premises such as hairdresser’s, cleaning

company, painter’s, etc. where chloride

products, solvents, paints, dust, etc. are

likely to contaminate the air, make sure

to install the appliance in a dedicated

boiler room so that the appliance is sup-

plied with clean combustion air.

Install a condensate neutralisation

system according to the applicable lo-

cal regulations and standards.

If the boiler is intended to be used

with G31 liquefi ed petroleum gas

(propane), installing the boiler below

ground level can be hazardous and

prohibited in some countries. Please

refer to applicable local regulations

for installation requirements.

Содержание N 280 FS





















































































Результаты поиска

Содержание N 280 FS

Отзывы:

Бренды по названию

Популярные бренды

AIC N 280 FS, Руководство по установке и обслуживанию

Результаты поиска

Содержание N 280 FS

Отзывы:

Бренды по названию

Популярные бренды