MACHINE DESCRIPTION
MARVEL 8 MARK III
© MARVEL MFG. CO., INC. MANUAL 8SDN10871N (04/08)
D-9
OPTIONAL EQUIPMENT
The following equipment can be installed by
customer as optional equipment on the Marvel
Series 8.
SECOND MACHINE VISE
(Option code E4).
A second machine vise operates similar to a
standard machine vise. A second machine vise
can be use to provide clamping on both sides of
the saw blade.
HIGH JAW VISE - COMPLETE
(Option
code E5). This is a complete vise assembly
including additional vise ratchets. This option is
recommended when cutting stock larger than
12" (305mm) in diameter. These vise jaws
install similar to the standard vise jaws but
permit mitered cuts only on the side opposite the
vise jaws. For mitered cuts on the large stock,
see option E15 (60
o
High Vise Jaws).
HIGH VISE JAWS - JAWS ONLY
(Option
code E6). Same as option E5 but does not
include ratchets. Existing vise ratchets must be
used.
60º HIGH JAW VISE - COMPLETE
(Option
code E15). This is a complete vise assembly
including additional vise ratchets. This option is
recommended when miter cutting stock larger
than 12" (305mm) in diameter. These vise jaws
install similar to the standard vise jaws.
60º HIGH VISE JAWS – JAWS ONLY
(Option code E16). Same as option E15 above,
but does not include vise ratchets. Existing vise
ratchets must be used.
LENGTH GAUGE – SAW TABLE
(Option
code E8). This length gauge installs in a T-slot
in the saw table and can be set to any pre-
measured length up to 10.5" (268mm). A single
locking knob locks the gauge in position for
rapid, multiple cuts to the same length.
AIR OPERATED VISE RATCHET
(Option
code E14). This air operated ratchet replaces a
standard vise ratchet for rapid clamping of the
stock. This option requires a user supplied air
source.
HIGH SAW COLUMN
(Option code M6).
This option, available only factory installed,
uses a saw column which is 6" (152mm) higher
than the standard Series 8 saw column. This
option increases the saw's vertical capacity from
22" (558mm) to 28" (711mm) at 90
o;
from
12.75" (324mm) to 17" (432mm) at 45
o
and
from 13.0" (330mm) to 17.2" (437mm) at 60
o
.
This option requires a longer blade. See
previous Specifications section.
DEAD ROLLER TABLE
(Option code F055).
This option increases the saw's material
handling capacity by adding a 5'0" (1524 mm)
roller table to either side of the machine. This
option attaches directly to the basic saw and
includes five ball bearing rollers, mounting
bracket and end stop. The weight capacity of the
roller table is 800 lb/ft (1212kg/m).
Installation of a dead roller table is described in
Marvel Bulletin 8-4 which is included with
every roller table.
EXTENSION ROLLER TABLE
(Option
code X055). Extension roller tables are used to
extend the length of a dead roller table (Option
code F055) an additional 5'0" (1524 mm).
The weight capacity of an extension roller table
is 610 lb/ft (924kg/m). Extension roller tables
can not be attached to the basic saw, only to a
dead roller table.
ADDITIONAL ROLLERS
(Option code E13).
Additional rollers may be installed between the
existing rollers of a roller table for added stock
support. The roller table capacity remains the
same.
ECCENTRIC LIFT ROLLER
(Option code
E12). This roller replaces the first roller of a
dead roller table (Option code F055) and aides
in moving larger stock across the saw table by
raising the stock slightly above the saw table's
surface.
LENGTH GAUGE
(Option code E10). This
clamp-on style stop gauge can be mounted
anywhere on a dead roller table to allow
repetitive cuts of the same length.
COOLANT PAN
(Option code E11). This
coolant pan can be installed on any roller table
to capture coolant and carry it back to the saw.
Содержание marvel 8 mark III Series
Страница 6: ...This page intentionally left blank...
