AGRU SP 63-M Скачать руководство пользователя страница 6

Version October 2014

EN

 7

agru SP 63-mobile User’s Manual

Important

 

Power Only to Operational Machine

Power must never be applied to the machine before it is com-
pletely installed and ready for operation.

Info

User’s Manual

The User’s Manual has to be available at any time on the site 
where the machine is used. If the User’s Manual should come 
to be incomplete or illegible replace it without delay. Feel free 
to contact us for assistance.

2.4 User/Operator 

Obligations

The machine may be operated exclusively by persons who are fa-
miliar with the applicable rules, the guidelines for the prevention of
accidents, and the User’s Manual.

The machine may be operated only when observed. Only persons
who were properly trained by agru or another, authorized organi-
zation and whose training was acknowledged by the appropriate
certificates are allowed to operate and observe the machine. Other
persons must neither operate nor observe it.

The operating/owning organization engages to check at reasonable
intervals if the machine is operated by the users with the intended
use and under proper guidelines of safe work.

The machine must never be operated if not in proper state of repair.
Before welding, the user is required to make sure that the state of
the machine is in order.

The user has to make sure that only one person is present in the
zone where the machine is operating.

2.5 Worksite 

Description

The conditions have to fully ensure that the machine cannot slide.
As well the segments of the base plate as the mechanical structure
and the base plate have to be securely connected to each other
before any components are clamped fast. In case of (overhead)
welding operations using the mechanical structure without the base
plate, the welding mechanics has to be securely fastened at the
components to be jointed with the supplied belts.

Worksite access limitations have to be provided. Appropriate equip-
ment to achieve this can be requested from a service point or the
selling entity.

2.6 Warranty

Warranty claims may be raised only if the conditions for warranty given 
in the General Terms and Conditions of Sale and Shipment obtain. Fur-
thermore, the provisions and instructions contained in the User’s Manual 
have to have been respected.

Info

The term of warranty under which the welding machine is 
shipped is 12 months:-
— from the date of purchase, if the machine is bought as a new 

 machine;

— from the date of first use, if the machine is used independently 

 of purchase (e.g. when lent) or if it is not bought as a new 

 machine.

2.7 

Transport and Storage

During transport, the machine must be at all times in the transport box 
it is shipped in.

Important

Ensure that the heating plate, the facing tool, and all movable/
removable parts of the machine are safely stowed away and, 

Содержание SP 63-M


























Отзывы: