Agilent Technologies U1401A Скачать руководство пользователя страница 172

Страница: 172 / 177

152

U1401A User’s and Service Guide

Specifications

Duty cycle

[1]

Pulse width

[1, 2]

[1]

The accuracy for duty cycle and pulse width is based on a 5 V square wave input
to the DC 5 V range.

[2]

Pulse width must be greater than 10 µs and its range and resolution are
determined by the frequency of the signal. Refer to

Table 8-8

for details.

Frequency sensitivity for current measurement

For maximum input, refer to AC voltage measurement.

Table 8-10

Duty cycle specifications

Mode

Range

Accuracy at full scale

DC coupling

0.1% to 99.9%

0.3% per kHz + 0.3%

AC coupling

5% to 95%

Table 8-11

Pulse width specifications

Range

Accuracy at full scale

0.01 ms to 1999.9 ms

0.2% + 3

Table 8-12

Frequency sensitivity specifications for current measurement

Input range

Minimum sensitivity (rms sine wave)

30 Hz to 20 kHz

50 mA

2.5 mA

500 mA

25 mA

Содержание U1401A


















































































































































































Результаты поиска

Содержание U1401A

Отзывы:

Похожие инструкции для U1401A

Бренды по названию

Популярные бренды

Agilent Technologies U1401A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1401A

Отзывы:

Похожие инструкции для U1401A

Бренды по названию

Популярные бренды