manualshive.com logo in svg

Agilent Technologies U1401A, Руководство пользователя и сервисное руководство, Страница: 51 / 177

Поделиться
Скачать
Agilent Technologies U1401A Скачать руководство пользователя страница 51

Calibrator Output Operations

2

U1401A User’s and Service Guide

31

Memory Generation

For constant voltage and current outputs, the U1401A offers 
two additional useful functions. One is an 

autoscan

 output 

that is able to generate up to 16 different steps of constant 
voltage or current each with its own user- defined amplitude 
and time interval. The other one is an 

autoramp

 output 

with user- defined dual slopes and number of steps for linear 
simulation.

Autoscan output

To set the 

autoscan

 output:

1

Turn the rotary switch to any one of the 

(constant 

current output) or 

 (constant voltage output) 

positions.

2

Press 

SHIFT

 to access the shifted operations of the keypad. 

The 

 annunciator will appear on the display.

3

Follow one of the instructions below:

•

For voltage output, press 

MODE

 to cycle through ±1.5 V, 

±15 V, 

 ±1.5 V, 

 ±15 V, 

 ±1.5 V, and 

 ±15 V output modes. Select one of the two 

 output modes, depending on the voltage range 

you require.

•

For current output, press 

MODE

 to cycle through 

±25 mA, 

 ±25 mA, and 

 ±25 mA output 

modes. Select the 

 output mode.

Содержание U1401A


















































































































































































Отзывы:

Нет отзывов