Agilent Technologies U1401A Скачать руководство пользователя страница 106

Страница: 106 / 177

U1401A User’s and Service Guide

Application Examples

Source Mode for mA Output

This instrument provides steady, stepped, and ramped
current output for testing 0 mA to 20 mA and 4 mA to
20 mA current loops.

The source mode can be used to supply current to a passive
circuit such as a current loop without loop supply.

Turn the rotary switch to the

position.

Plug the red and black banana plugs of the alligator leads
into the positive (+) and negative (–) output terminals
respectively.

Connect the red and black alligator clips to the current
loop. Make sure that the polarity is correct.

Press

SHIFT

to access the shifted operations of the keypad.

The

annunciator will appear on the display.

Set the output level at

08.000

mA to get a 25% scale

readout for 4 mA to 20 mA.

Press

OUTPUT

to start the source output. The

annunciator will appear on the display.

You can use autoscan to test the loop with varying levels of
current output. Refer to

Chapter 2

, “Autoscan output,” on

page 31 for more information on the memory default values.

Содержание U1401A


















































































































































































Результаты поиска

Содержание U1401A

Отзывы:

Похожие инструкции для U1401A

Бренды по названию

Популярные бренды

Agilent Technologies U1401A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1401A

Отзывы:

Похожие инструкции для U1401A

Бренды по названию

Популярные бренды