Agilent Technologies U1401A Скачать руководство пользователя страница 32

Страница: 32 / 177

U1401A User’s and Service Guide

Getting Started

Shifted functions

Every key (except the

SHIFT

key itself) has a shifted function.

To access these shifted functions, you must first press

SHIFT

After pressing

SHIFT

, the shifted functions will remain

enabled (the LCD display will indicate

) until the

SHIFT

key is pressed again.

Throughout this manual, instructions that involve shifted
functions will be given without explicit mention of the

SHIFT

key. Refer to

Table 1- 5

on page 12 for a list of such

instructions and what you will need to do.

[1]

If the shifted functions are not already enabled.

Table 1-5

Instructions involving shifted functions

Instruction

Required actions

Press

MODE

Press

SHIFT

[1]

, then press

Press Press

SHIFT

[1]

, then press

Press Press

SHIFT

[1]

, then press

Press Press

SHIFT

[1]

, then press

Press Press

SHIFT

[1]

, then press

Press

OUTPUT

Press

SHIFT

[1]

, then press

3
4
5
6

Содержание U1401A


















































































































































































Результаты поиска

Содержание U1401A

Отзывы:

Agilent Technologies U1401A, Руководство пользователя и сервисное руководство, Страница: 32 / 177

Результаты поиска

Содержание U1401A

Отзывы: