Agilent Technologies U1401A Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 177

background image

U1401A User’s and Service Guide

Notices

© Agilent Technologies, Inc. 2009 - 2012

No part of this manual may be reproduced in
any form or by any means (including elec-
tronic storage and retrieval or translation
into a foreign language) without prior agree-
ment and written consent from Agilent
Technologies, Inc. as governed by United
States and international copyright laws.

Manual Part Number

U1401-90001

Edition

Fourth Edition, May 4, 2012

Printed in Malaysia

Agilent Technologies, Inc.
3501 Stevens Creek Blvd.
Santa Clara, CA 95052 USA

Warranty

The material contained in this docu-
ment is provided “as is,” and is sub-
ject to being changed, without notice,
in future editions. Further, to the max-
imum extent permitted by applicable
law, Agilent disclaims all warranties,
either express or implied, with regard
to this manual and any information
contained herein, including but not
limited to the implied warranties of
merchantability and fitness for a par-
ticular purpose. Agilent shall not be
liable for errors or for incidental or
consequential damages in connec-
tion with the furnishing, use, or per-
formance of this document or of any
information contained herein. Should
Agilent and the user have a separate
written agreement with warranty
terms covering the material in this
document that conflict with these
terms, the warranty terms in the sep-
arate agreement shall control.

Technology Licenses

The hardware and/or software described in
this document are furnished under a license
and may be used or copied only in accor-
dance with the terms of such license.

Restricted Rights Legend

U.S. Government Restricted Rights. Soft-
ware and technical data rights granted to
the federal government include only those
rights customarily provided to end user cus-
tomers. Agilent provides this customary
commercial license in Software and techni-
cal data pursuant to FAR 12.211 (Technical
Data) and 12.212 (Computer Software) and,
for the Department of Defense, DFARS
252.227-7015 (Technical Data - Commercial
Items) and DFARS 227.7202-3 (Rights in
Commercial Computer Software or Com-
puter Software Documentation).

Safety Notices

C A U T I O N

A

CAUTION

notice denotes a haz-

ard. It calls attention to an operat-
ing procedure, practice, or the like
that, if not correctly performed or
adhered to, could result in damage
to the product or loss of important
data. Do not proceed beyond a

CAUTION

notice until the indicated

conditions are fully understood and
met.

WA R N I N G

A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly per-
formed or adhered to, could result
in personal injury or death. Do not
proceed beyond a WARNING
notice until the indicated condi-
tions are fully understood and
met.

«
1
2
3
4
...
»

Содержание U1401A


















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для U1401A

VBOX Micro RLVBMIC01

Бренд: Racelogic Страницы: 29

Бренд: Extech Instruments Страницы: 12

WineCap WSD12-THEE

Бренд: Capetti Elettronica Страницы: 7

Бренд: B+B Sensors Страницы: 19

Бренд: Loggerflex Страницы: 20

Бренд: RS PRO Страницы: 16

Бренд: Chauvin Arnoux Страницы: 80

Бренд: Vaisala Страницы: 97

Bently Nevada SCOUT200 Series

Бренд: GE Страницы: 6

Synergy Compact

Бренд: Tidal Engineering Страницы: 346

Бренд: Tinytag Страницы: 5

Бренд: Senonics Страницы: 6

Бренд: Senonics Страницы: 11

Бренд: Noraxon Страницы: 24

Бренд: Noraxon Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды