manualshive.com logo in svg

Agilent Technologies Infiniium 90000 A, Руководство по обслуживанию

Поделиться
Скачать
Agilent Technologies Infiniium 90000 A Скачать руководство пользователя страница 90

90

Replacing Assemblies

Use the procedures in this chapter when removing and replacing assemblies and parts 
in the Agilent Technologies oscilloscopes.

In general, the procedures that follow are placed in the order to be used to remove a 
particular assembly. The procedures listed first are for assemblies that must be removed 
first.

The graphics in this chapter are representative of the oscilloscope at the time of this 
printing. Your unit may look different.

ESD Precautions

When using any of the procedures in this chapter you must use proper ESD precautions. 
As a minimum you must place the oscilloscope on a properly grounded ESD mat and 
wear a properly grounded ESD wrist strap.

C A U T I O N

AVOID DAMAGE TO THE OSCILLOSCOPE!
Failure to implement proper antistatic measures may result in damage to the oscilloscope.

Tools Required

The following tools are required for these procedures.

• Torx drivers: T10, T20

• Socket wrench: 9/16 inch

• Torque wrench: 3.5 mm (8 in-lbs)

• Medium size (3/16-in) flat-blade screwdriver

C A U T I O N

REMOVE POWER BEFORE REMOVING OR REPLACING ASSEMBLIES!
Do not remove or replace any circuit board assemblies in this oscilloscope while power is applied. 
The assemblies contain components which may be damaged if the assembly is removed or 
replaced while power is connected to the oscilloscope.

W A R N I N G

SHOCK HAZARD!
To avoid electrical shock, adhere closely to the following procedures. Also, after disconnecting 
the power cable, wait at least three minutes for the capacitors on the power supply to discharge 
before servicing this oscilloscope. Hazardous voltages exist on the inverter for the display 
monitor.

W A R N I N G

SHOCK HAZARD!
Read the Safety information at the back of this guide before performing the following procedures. 
Failure to observe safety precautions may result in electrical shock.

W A R N I N G

INJURY CAN RESULT!
Use caution when the oscilloscope fan blades are exposed as they can cause injury.

Содержание Infiniium 90000 A





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды