manualshive.com logo in svg

Agilent Technologies Infiniium 90000 A, Руководство по обслуживанию

Поделиться
Скачать
Agilent Technologies Infiniium 90000 A Скачать руководство пользователя страница 124

Chapter 5: Replacing Assemblies
To remove and replace the power cord

124

To remove and replace the power cord

Use this procedure to remove and replace the power cord. When necessary, refer to other 
removal procedures. The graphics in this chapter are representative of the oscilloscope at the 
time of this printing. Your unit may look different.

1

Disconnect the power cable and remove the cover and top plate.

2

Unplug the power cable from the 12V power supply (refer to Figure 5-52 for the location 
of this connection).

3

Unscrew the power cord connector from rear panel (Torx T10 screws) - see Figure 5-54.

Figure 5-54

4

Remove the ground screw (Torx T10) on right side of hard drive (Figure 5-55).

Figure 5-55

5

Pull the power cord out of the instrument.

6

To replace the power cord, reverse these directions.

Содержание Infiniium 90000 A





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды