manualshive.com logo in svg

Agilent Technologies Infiniium 90000 A, Руководство по обслуживанию

Поделиться
Скачать
Agilent Technologies Infiniium 90000 A Скачать руководство пользователя страница 135

Chapter 6: Replaceable Parts

Replaceable Parts List

135

MP18

54913-00103

1

RHDD Deck

MP19

54913-94306

1

Label - Rear Panel without RHDD

MP20

54913-62301

1

Accessory Pouch

MP21

54913-94307

1

RHDD Label

MP22*

54913-04101*

1

Cover (standard models)

MP22**

54916-04101**

1

Cover (performance-enhanced models)

MP23

54913-41001

2

Rear Foot

MP24

54913-44101

1

Front Cover

MP25*

E4400-60026*

1

Handle Assembly (standard models)

MP25**

54916-64901**

1

Handle - Strap Assembly (performance-enhanced models -- order twice if you 
want to replace both handles)

MP26*

54913-94309*

1

Label - PC i/o (standard models)

MP26**

54916-94309**

1

Label - PC i/e (performance-enhanced models)

MP27

54855-67601

5

Female Connector Assembly coaxial adapter

54916-22401**

2

Screws for Side Handles (performance-enhanced models)

54913-94308*

1

Label - PC Rear Panel (standard models)

54916-94308**

1

Label - PC Rear Panel (performance-enhanced models)

W1

54913-61610

1

Cable - AC Input

W2

54913-61602

1

Cable - semi-rigid auxiliary output

W3

54913-61613

1

Cable - USB Host

W4

54913-61603

1

Cable - PC Power (not shown)

W5

54913-61611

1

Cable - Fan (not shown)

W6

54913-61604

1

Cable - ON/OFF (not shown)

W7

54913-61608

1

Cable - Display (not shown)

W8

54913-61601

4

Cable - Input (not shown)

54913-61607*

1

Cable - USB Touch (standard models)

54913-61617**

1

Cable - USB Touch (performance-enhanced models)

8120-5392

1

Power cord - United Kingdom

8120-5393

1

Power cord - Australia and New Zealand

8120-5336

1

Power cord - Continental Europe

8120-5395

1

Power cord - United States and Canada

8120-5397

1

Power cord - Switzerland

8120-5398

1

Power cord - Denmark

8120-5399

1

Power cord - India

8120-5400

1

Power cord - Japan

8121-0955

1

Power cord - Israel

8120-8390

1

Power cord - Argentina

8120-8389

1

Power cord - Chile

8121-1632

1

Power cord - China

8120-5399

1

Power cord - South Africa

8121-1660

1

Power cord - Thailand

8121-1858

1

Power cord - Brazil

8121-1636

1

Power cord - Taiwan

8121-1640

1

Power cord - Cambodia

* Parts marked with a single asterisk are to be used only with the standard models (not performance-enhanced models). For 
information on how to tell which model you have, refer to page 9.
** Parts marked with a double asterisk are to be used only with the performance-enhanced models (not standard models). For 
information on how to tell which model you have, refer to page 9.

Replaceable Parts

Ref.
Des.

Agilent Part
Number

QTY

Description

Содержание Infiniium 90000 A





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды