manualshive.com logo in svg

Agilent Technologies Infiniium 90000 A, Руководство по обслуживанию

Поделиться
Скачать
Agilent Technologies Infiniium 90000 A Скачать руководство пользователя страница 16

Chapter 2: Calibration
To run the self calibration

16

Figure 2-1   

Calibration Dialog

 Box

4

Click Start, then follow the instructions on the screen. 

The routine will ask you to do the following things in sequence:

a

Decide if you want to perform the Time Scale Calibration.  Your choices are:

• Standard Calibration - Time scale calibration will not be performed.  Time scale 

calibration factors from the previous time scale calibration will be used and the 10 MHz 
reference signal will not be required.  The remaining calibration procedure will continue.

• Standard Calibration and Time Scale Calibration - Performs the time scale calibration.  

This option requires you to connect a 10 MHz reference signal to channel 1 that meets 
the following specifications. Failure to use a reference signal that meets this specification 
will result in an inaccurate calibration.

• Standard Calibration and Reset Time Scalie Calibration - Factory time scale calibration 

factors will be used.  The 10 MHz reference signal will not be required.  The remaining 
calibration procedure will continue.

b

Disconnect everything from all inputs and Aux Out.

c

Connect the calibration cable from Aux Out to channel 1.

You must use the 54855-61620 cable assembly with two 54855-67604 adapters for all 
oscilloscopes except for the DSO90254A which can use a good quality BNC cable.  Failure 
to use the appropriate calibration cable will result in an inaccurate calibration.

d

Connect the calibration cable from Aux Out to each of the channel inputs as requested.

e

Connect the 50 

Ω

 BNC cable from the Aux Out to the Aux Trig on the front panel of the 

oscilloscope.

f

A Passed/Failed indication is displayed for each calibration section.  If any section fails, 
check the calibration cables and run the oscilloscope Self Test in the Utilities menu.  
Page 87 also has a little section on what to do if a self cal fails in terms of replacing 
assemblies.

5

After the calibration procedure is completed, click Close.

Click here to start 
calibration

Clear this check 
box before starting 
calibration

Frequency: 10 MHz ±0.4 ppm = 10 MHz ±4 Hz
Amplitude: 0.2 Vpeak-to-peak to 5.0 Vpeak-to-peak
Wave shape: Sine or Square

Содержание Infiniium 90000 A





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды