manualshive.com logo in svg

Agilent Technologies Infiniium 90000 A, Руководство по обслуживанию

Поделиться
Скачать
Agilent Technologies Infiniium 90000 A Скачать руководство пользователя страница 128

128

Replaceable Parts    

This chapter describes how to order replaceable assemblies and parts for the Agilent 
90000 A-Series oscilloscopes. Service support for this oscilloscope is replacement of 
parts to the assembly level.

Ordering Replaceable Parts

Listed Parts

To order a part in the parts list, quote the Agilent Technologies part number, indicate the quantity 
desired, and address the order to the nearest Agilent Technologies Sales Office.

Unlisted Parts

To order a part not listed in the parts list, include the oscilloscope part number, oscilloscope 
serial number, a description of the part (including its function), and the number of parts required. 
Address the order to the nearest Agilent Technologies Sales Office.

Direct Mail Order System    

Within the USA, Agilent Technologies can supply parts through a direct mail order system. There 
are several advantages to this system:

• Direct ordering and shipping from the Agilent Technologies parts center in California, USA.

• No maximum or minimum on any mail order. (There is a minimum amount for parts ordered 

through a local Agilent Technologies Sales Office when the orders require billing and 
invoicing.)

• Prepaid transportation. (There is a small handling charge for each order.)

• No invoices.

In order for Agilent Technologies to provide these advantages, please send a check or money 
order with each order.

Mail order forms and specific ordering information are available through your local Agilent 
Technologies Sales Office. Addresses and telephone numbers are located in a separate document 
shipped with the manuals.

Exchange Assemblies

Exchange assemblies have been set up for Agilent Service Center use only.

Содержание Infiniium 90000 A





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды