Agilent Technologies 66319B Скачать руководство пользователя страница 65

Страница: 65 / 180

Introduction to Programming - 6

SCPI Data Formats

All data programmed to or returned from the dc source is ASCII. The data may be numerical or character
string.

Numerical Data Formats

Symbol Response

Formats

<NR1>

Digits with an implied decimal point assumed at the right of the least-significant digit.
Examples:

273

<NR2>

Digits with an explicit decimal point. Example:

.0273

<NR3>

Digits with an explicit decimal point and an exponent. Example:

2.73E+2

Parameter

Formats

<Nrf>

Extended format that includes

<NR1>, <NR2> and <NR3>.

Examples:

273 273. 2.73E2

<Nrf+>

Expanded decimal format that includes

<NRf>

and

MIN MAX

. Examples:

273 273.

2.73E2 MAX. MIN

and

MAX

are the minimum and maximum limit values that are

implicit in the range specification for the parameter.

<Bool>

Boolean Data. Example:

0 | 1

ON | OFF

Suffixes and Multipliers

Class Suffix Unit

Unit with Multiplier

Current A

ampere MA

(milliampere)

Amplitude V volt

(millivolt)

Time S

second MS

(millisecond)

Common Multipliers

1E3

kilo

1E-3

milli

1E-6

micro

Response Data Types

Character strings returned by query statements may take either of the following forms, depending on the
length of the returned string:

<CRD>

Character Response Data. Permits the return of character strings.

<AARD>

Arbitrary ASCII Response Data. Permits the return of undelimited 7-bit ASCII. This data
type has an implied message terminator.

<SRD>

String Response Data. Returns string parameters enclosed in double quotes.

Содержание 66319B





















































































































































































Результаты поиска

Содержание 66319B

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 66319B, Руководство пользователя

Результаты поиска

Содержание 66319B

Отзывы:

Бренды по названию

Популярные бренды