Agilent Technologies 66319B Скачать руководство пользователя страница 48

Страница: 48 / 180

5 – Front Panel Operation

Output Control Keys

Output control keys control the output functions of the dc source.

Press this key to access the voltage menu.

Display

Command

Function

VOLT <value>

Sets the voltage of output 1 (the main output of all models)

VOLT <value>

Sets the voltage of output 2

LIMIT <char>

Sets the programmable voltage limit

(

output 1 shown

)

Press this key to access the current menu.

Display

Command

Function

CURR <value>

Sets the current of output 1 (the main output of all models)

CURR <value>

Sets the current of output 2

Press this key to access the resistance menu.

Display

Command

Function

RES <value>

Sets the resistance of output 1 (the main output of all models)

Press this key to access the output menu list.

Display

Command

Function

*RST

Places the dc source in the factory-default state

COUPLING <char>

Couples or decouples output 1 and output 2 (NONE | ALL)

COMP <char>

Sets output compensation

(HREMOTE | LREMOTE | HLOCAL | LLOCAL)

PON:STATE <char>

Select the power-on state command (RST | RCL0)

PROT:DLY <value>

Sets the output protection delay in seconds

RI <char>

Sets the remote inhibit mode (LATCHING | LIVE | OFF)

DFI <char>

Sets the discrete fault indicator state (ON | OFF)

DFI:SOUR <char>

Selects the DFI source (QUES | OPER | ESB | RQS | OFF)

PORT <char>

Sets the output port functions (RIDFI | DIGIO | TRIGGER)

DIGIO <char>

Sets and reads the I/O port value (0 through 7)

SENSE:PROT<char>

Enables or disables the open sense lead detect circuit (ON | OFF)

REL:MODE <char>

Sets the relay mode for option 521units

(DD, HD, DH, or HH)

(applies to both outputs; output 1 shown)

Press this key to display protection status.

Display

Command

Function

OVER CURRENT

Status of the protection features (example shows overcurrent)

NO FAULT

Status of the protection features (example shows none tripped)

Press this key to access the overvoltage protection menu.

Display

Command

Function

PROT:STAT <char>

Enables or disables overvoltage protection (ON | OFF)

This key accesses the calibration menu (Refer to Appendix B for details).

Notes:

These parameters are explained in chapter 3.

These status summary bits are explained in chapter 7.

These relay modes are explained in chapter 2

value = a numeric value

char = a character string parameter

Use and to scroll through the menu commands.

Use and to scroll through the menu parameters.

Use and to select a digit in a numeric entry field.

Voltage

Current

Res

Shift

Output

Protect

Shift

Cal

Shift

(

Содержание 66319B





















































































































































































Результаты поиска

Содержание 66319B

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 66319B, Руководство пользователя

Результаты поиска

Содержание 66319B

Отзывы:

Бренды по названию

Популярные бренды